Description Display the Imsi and Imei value | NordicTrack 3G10WV

System mode: WCDMA PS state: Attached

WCDMA band: WCDMA800 GSM band: Unknown

WCDMA channel: 4436 GSM channel: 65535 GMM (PS) state:REGISTERED NORMAL SERVICE MM (CS) state: IDLE NORMAL SERVICE

WCDMA L1 State:L1M_FACH RRC State: CELL_FACH

RX level (dBm):-90

IMSI & IMEI read

Description: Display the IMSI and IMEI value

Synopsis: sierra show --imsi sierra show --imei

Example:

>sierra show --imsi imsi: 466974800524867

>sierra show --imei IMEI: 354219010024303 Network Information

•sierra show --hsdcat

Description: To indicate the current HSDPA category.

Synopsis: sierra show --hsdcat Example:

>sierra show --hsdcat !HSDCAT: 8

•sierra show --hsucat

Description: To indicate the current HSUPA category.

Synopsis: sierra show --hsucat

Example:

>sierra show --hsucat !HSUCAT: 5

•sierra show --mode

3G10WV HSPA Wi-Fi Router with Voice – 77

Image 77

NordicTrack 3G10WV Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90, Description Display the Imsi and Imei value

Contents

3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Preface Important Notice and Safety Precaution Table of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents Features Associated port LED IndicatorsColor Mode Description Rear Panel Quick Setup Setup Procedure Quick SetupConfigure the router through the Web User Interface WUI Save the router configuration and reboot see section Web User Interface Web User Interface Default Settings Click OK to submit the settings TCP/IP SettingsDhcp Mode To login to the web interface, follow the steps below Login Procedure Basic / Home Web User Interface Homepage Fields Description Following table provides further details 3G Settings This menu includes 3G service Setup and PIN Configuration 3G Settings3G Service Setup 20 3G10WV Hspa Wi-Fi Router with Voice PIN Lock Off PIN ConfigurationPIN Code Protection PIN Lock On PIN Code Change Wireless Wireless Option Description Setup Security Click Save/Apply to configure the wireless security options Authentication Card. If the Ssid does not match, access is deniedWEP Encryption will also be enabled Select Ssid Configuration Default is disabled Broadcast and multicast messages. The default isAP Isolation Point can be linked Only mode 54g ModeMbit/s Dsss specification as described in Ieee Std 54g Protection MAC Filter Deny Rejects access for the specified MAC addressesMAC Address Can be added Feature Options Wireless BridgeClick Save/Apply to implement new configuration settings Station Info Authorized Lists those devices with authorized accessIs generated randomly Associated Management Management Device Settings Restore Default Update Settings 38 3G10WV Hspa Wi-Fi Router with Voice Setting up Snmp agent Configure Snmp agent on 3G10WVBy default, Snmp agent is enabled on the gateway Press Save/Apply to activate setting Simple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced Setup These options are used for special Dhcp set up Setting. By default NAT is enabledHosts connected to Hspa 7.2 Mbps Wi-Fi Router Local Area Network LAN Enable Dhcp Server Enable DhcpShow up on the same page as below Server Relay Port Forwarding Network Address Translation NAT Selected the port ranges are automatically configured Is selected the port ranges are automatically configuredOptions Description External Port End Port Triggering Trigger Port End Demilitarized DMZ HostTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port End 52 3G10WV Hspa Wi-Fi Router with Voice Options Description MAC address of the PC running the browser Parental ControlUser Name User-defined label for this restriction Routing 56 3G10WV Hspa Wi-Fi Router with Voice Domain Name Servers DNS DNS Server Configuration Options Descriptions Dynamic DNS Voice Voice Configuring your 3G10WV for placing Voice Calls Status Status Test Description Diagnostics System Log Click View System Log. The results are displayed as follows 3G Status Status Description Status Status BCS Battery Charge LevelQuality Ec/Io Strongest cells Network Registration Interface Shows connection interfaces Statistics Service Shows the service type Select Route to display the paths the Router has found RouteField Description But may be needed by routing daemons ARP Dynamic Host Configuration Protocol DhcpClick ARP to display the ARP information Click Dhcp to display the Dhcp information Ping CLI commands Via Telnet Help CLI commands via TelnetEnd the telnet session Synopsis help ? Example Examples Description Display the 3G network connection status Description Display the Imsi and Imei value Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Sierra show --mode Sierra show --hsdcat !HSDCAT Synopsis sierra set --apn profile apn profile 1 Custom APN Sierra show --mode mode UmtsExample Set the Custom APN to test.test Sierra show -auth 1 Profile1 PAP Synopsis sierra set --comp profile type enabledisableExample Enable the IP header compression for Custom APN Connect / Disconnect PPP session PIN code configuration Sierra set --PIN-CHG 0000 Synopsis sierra show --PIN-LOCK ExampleChanged the PIN code successfully PUK code unlock Sierra set --PUK 11111111 0000 PUK unlock successfully Wlan Options Enable Valid value 32 characters string --country countryStr Description Set the wireless LAN channel Valid value 0~14Means auto select channel. Default value Default value 2346 --dtim dtimInterval Default value 0 --mrate rateVal Example Default value long Options Example Synopsis Configure wireless LAN MAC filterRemove MACaddress Options Description add one MAC Address entry --remove MACaddress Description set remote bridge MAC address Wlan security wpaGTKRekey = Advance Wlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information