Examples | NordicTrack 3G10WV instruction

Description: End the telnet session

Synopsis: logout

Example:

>logout Reset/reboot device Description: To reboot the router. Synopsis: reboot

Example:

>reboot

Radio Signal Strength

Description: Display the 3G radio signal strength.

Synopsis: sierra show --signal

Example:

>sierra show --signal signal: 23

Note: Signal value is explain in the table below

Radio Band

Description: Display the 3G band

Synopsis: sierra show --band

Example:

>sierra show --band band: IMT2000

Note: IMT2000 is band 2100 and WCDMA800 is band 850 Connection status

Description: Display the 3G network connection status

Synopsis: sierra show –link sierra show --gstatus

Examples:

>sierra show --link link: Connected

>sierra show --gstatus

Current Time: 450 Temperature: 45

Bootup Time: 1 Mode: ONLINE

76 – 3G10WV HSPA Wi-Fi Router with Voice

Image 76

NordicTrack 3G10WV manual Description Display the 3G network connection status, Examples

Contents

3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Important Notice and Safety Precaution Preface Table of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Features Package Contents Color Mode Description LED IndicatorsAssociated port Rear Panel Quick Setup Quick Setup Setup ProcedureConfigure the router through the Web User Interface WUI Save the router configuration and reboot see section Web User Interface Default Settings Web User Interface Dhcp Mode TCP/IP SettingsClick OK to submit the settings Login Procedure To login to the web interface, follow the steps below Web User Interface Homepage Basic / Home Following table provides further details Fields Description 3G Settings 3G Service Setup 3G SettingsThis menu includes 3G service Setup and PIN Configuration 20 3G10WV Hspa Wi-Fi Router with Voice PIN Code Protection PIN ConfigurationPIN Lock Off PIN Lock On PIN Code Change Wireless Wireless Setup Option Description Click Save/Apply to configure the wireless security options Security Card. If the Ssid does not match, access is denied AuthenticationWEP Encryption will also be enabled Select Ssid Configuration Broadcast and multicast messages. The default is Default is disabledAP Isolation Point can be linked 54g Mode Only modeMbit/s Dsss specification as described in Ieee Std 54g Protection Deny Rejects access for the specified MAC addresses MAC FilterMAC Address Can be added Click Save/Apply to implement new configuration settings Wireless BridgeFeature Options Authorized Lists those devices with authorized access Station InfoIs generated randomly Associated Management Device Settings Management Update Settings Restore Default 38 3G10WV Hspa Wi-Fi Router with Voice Configure Snmp agent on 3G10WV Setting up Snmp agentBy default, Snmp agent is enabled on the gateway Press Save/Apply to activate setting Simple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup Advanced Setup This chapter explains advanced setup for your Router Setting. By default NAT is enabled These options are used for special Dhcp set upHosts connected to Hspa 7.2 Mbps Wi-Fi Router Local Area Network LAN Enable Dhcp Enable Dhcp ServerShow up on the same page as below Server Relay Network Address Translation NAT Port Forwarding Is selected the port ranges are automatically configured Selected the port ranges are automatically configuredOptions Description External Port End Port Triggering Demilitarized DMZ Host Trigger Port EndTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port End 52 3G10WV Hspa Wi-Fi Router with Voice Options Description User Name User-defined label for this restriction Parental ControlMAC address of the PC running the browser Routing 56 3G10WV Hspa Wi-Fi Router with Voice DNS Server Configuration Domain Name Servers DNS Dynamic DNS Options Descriptions Voice Configuring your 3G10WV for placing Voice Calls Voice Status Status Diagnostics Test Description System Log Click View System Log. The results are displayed as follows 3G Status Status Description Status BCS Battery Charge Level StatusQuality Ec/Io Strongest cells Network Registration Statistics Interface Shows connection interfaces Service Shows the service type Route Select Route to display the paths the Router has foundField Description But may be needed by routing daemons Dynamic Host Configuration Protocol Dhcp ARPClick ARP to display the ARP information Click Dhcp to display the Dhcp information Ping CLI commands Via Telnet CLI commands via Telnet HelpEnd the telnet session Synopsis help ? Example Description Display the 3G network connection status Examples Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90 Description Display the Imsi and Imei valueSierra show --mode Sierra show --hsdcat !HSDCAT Example Set the Custom APN to test.test Sierra show --mode mode UmtsSynopsis sierra set --apn profile apn profile 1 Custom APN Example Enable the IP header compression for Custom APN Synopsis sierra set --comp profile type enabledisableSierra show -auth 1 Profile1 PAP PIN code configuration Connect / Disconnect PPP session Synopsis sierra show --PIN-LOCK Example Sierra set --PIN-CHG 0000Changed the PIN code successfully PUK code unlock Sierra set --PUK 11111111 0000 PUK unlock successfully Options Enable Wlan Means auto select channel. Default value Description Set the wireless LAN channel Valid value 0~14Valid value 32 characters string --country countryStr Default value 0 --mrate rateVal Default value 2346 --dtim dtimInterval Default value long Example Options Example Configure wireless LAN MAC filter SynopsisRemove MACaddress Options Description add one MAC Address entry --remove MACaddress Description set remote bridge MAC address Advance Wlan security wpaGTKRekey = Wlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information