Media Access Control address | Nortel Networks 600r specs

Connecting the server to the Nortel server subnet (optional) 33

Note: The ELAN connector is labeled 2 on the rear panel of the server. For the connector location, refer to diagram Figure 12 "Rear panel" (page 40), label H on the diagram.

2Connect an RJ-45 network cable from the ELAN Ethernet switch or hub to the server’s ELAN connector.

Note: The ELAN Ethernet switch or hub is optional if you use a crossover network cable to make a direct point-to-point connection from the server to the switch. However, if you choose to establish a direct point-to-point ELAN connection, no other device can connect to the ELAN subnet. For speciﬁc connection details, see the CS 1000 network documentation.

—End—

What is next?

If the server	Then
is connected to a Nortel server	continue with "Connecting the server to the
subnet	Nortel server subnet (optional)" (page 33).

is not connected to a Nortel server	continue with installing the software feature
subnet	dongle. See "Installing the Nortel software
	feature dongle" (page 34).

Connecting the server to the Nortel server subnet (optional)

This section provides instructions to connect the server to the Nortel server subnet.

Note: The CLAN connection is optional. However, connection to a Nortel server subnet is required for support of desktop and Web messaging users, or administration by means of a Web-enabled PC. Ensure that CallPilot has the latest antivirus software. Do not install third-party antivirus software unless approved by Nortel. For information about the antivirus software packages that are approved by Nortel for CallPilot, see Product Bulletin P-2007-0101-Global : CallPilot Support for Anti-Virus Applications.

Media Access Control address

The Media Access Control (MAC) address is a unique number assigned to network cards and controllers. You can ﬁnd the MAC address bar code label located on top of the chassis, directly above the front main push-button

Nortel CallPilot

600r Server Hardware Installation

NN44200-307 01.03 Standard

5.014 May 2008

Copyright © 2007-2008, Nortel Networks

Image 33

Nortel Networks 600r manual Connecting the server to the Nortel server subnet optional, Media Access Control address

Contents

600r Server Hardware Installation Trademarks Information for Japan Japan Denan statementJapan Vcci statement Page Publication History MayMarch Publication History Contents Contents Chapter How to get help Getting help over the phone from a Nortel Solutions CenterGetting help from the Nortel Web site Getting help through a Nortel distributor or reseller Chapter 600r server description Conventions for WarningsThis chapter Server dimensions Server features Specification Front panel featuresEnvironmental speciﬁcations Environmental condition Front panel Power button NMI button not used Reset button ID button Rear panel controls and features Label DescriptionRear panel Label Description PCI riser assembly PCI riser assemblyNetwork connectivity Sample network setup Communication Server Sample network setup MeridianSample network setup with Meridian Sample network setup with Communication Server LAN connectivity Switch connectivity Supported peripheral devices Remote access connectivityNetwork requirements Supported peripheral devices Device Description Reference documents Installation overview Chapter Preparing for installationInstallation checklist Introduction Global CallPilot Support for Anti-Virus What is next? Unpacking the 600r serverTo unpack the equipment Inspecting the interior of server To remove the server coverTo replace the server cover Inspecting the interior of server Preparing for installation Installing the server Chapter Installing the server and peripheral devices Connecting peripherals to the server To install the serverRear panel connectors To connect the mouse, keyboard, and monitor to the server Rear panel Rear panel connectors Label Description To connect the external Scsi tape drive To connect the modem to the server Scsi tape drive with terminator Connecting the server to the Elan subnet Connecting the server to the Nortel server subnet optional Media Access Control addressIf the server Then To connect the server to the Nortel server subnet Installing the Nortel software feature dongle Dongle plugged in to server To install the software feature dongle Installing the software feature key Dongle without feature key Continue with Connecting the server to power Installing the server and peripheral devices Safety precautions Chapter Connecting the server to powerLocating the power supply modules Safety information About the power supply module Connecting the server to powerRack power and grounding Before you begin Connecting the server to power Example setup of 600r with peripherals To connect the 600r server to power What is next? Connecting the server to power Chapter EMC emission level protection for the 600r server Ferrite cores secured to an external cable Index Symbols/Numerics Index Index Index Page 600r Server Hardware Installation