Pacific Research Solutions RI-300e User Manual

Page 150

SECTION 21 SYSTEM COMMAND TABLE

S-Cmd Command Description

and Data Format Read Back

Syntax Command

Syntax Factory

Setting Stored

Location

00 No Operation
Used for clearing a macro area N/A 00 N/A N/A
01 System mode
Mode 0 = System off, 1 = COS, 2 = Rpt CTCSS/DCS,
3 = COS + Rpt CTCSS/DCS, 4 = Open squelch,
5 = Rpt audio off, 6 = PTT and repeat audio Off
7 = Rpt audio off, RX audio disabled when PTT active.
01 01 [Mode] 3
COS+
CTCSS
RAM
EEPROM
02 RX Audio source mode
Mode 0 = Pass sub audio, 1 = Reject sub audio 02 02 [Mode] 1
Reject sub
audio
RAM
EEPROM
03 Control Prefix Set up
Item 0 = Function Mode
Data 0 = Disable, 1 = Lockout, 2 = Local port,
3 = Link port
Item 1 = Prefix, 1-4 DTMF characters
Data = All DTMF characters
Item 2 = Aux Mute Character
Data = 0 (Disable), 1-9, 10-15 (A-D, *, #), 16 (0)
Item 3 = Command timer
Data = 25-255 in 100ms inc.
Item 4 = Active telemetry tone
Data = Four sets of 3 digit tone commands
Item 5 = Busy telemetry tone
Data = Four sets of 3 digit tone commands
03 [Item] 03 [Item] [Data] Item 0
0 (Disable)
Item 1
No prefix
Item 2
0 (Disable)
Item 3
80 (8.0 S)
Item 4
026 079
272 000
Item 5

028 079

293 329
RAM
EEPROM
04 Repeater carrier delay time
Time = 0 to 255 in 1/10 second increments 04 04 [Time] 30
3.0 Sec RAM
EEPROM
05 Force on repeater PTT for set time
Time = 0 to 3600 second 05 05 [Time] 0 Sec. Power
On
06 Repeater telemetry mode
Mode 0 = Disable, 1 = Suppress function complete/error
one time, 2 = CW ID only, 3 = CW & Speech ID only,
4 = CW function complete & ID only,
5 = CW & Speech function complete & ID only,
6 = CW only, 7= All on
06 06 [Mode] 7
All on RAM
EEPROM
07 ID interval time
Time = 0 to 255 in 6 seconds increments, 0 = disable 07 07 [Time] 10.0 Min.
RAM
EEPROM
08 Courtesy message timer, COS falling to start of message
Time = 0 to 99 in 1/10 second increments, 0 = disable 08 08 [Time] 1.5 Sec.
RAM
EEPROM
09 LED Status Display (lowers current drain)
Mode 0 = Disable (off), 1 = Enable (on) 09 09 [Mode] 1
on
RAM
EEPROM
10 Repeater time-out time
Time = 0 to 255 in 6 seconds increments,
0 = disable, * = Reset timer
10 10 [Time] 0
0.0 Min. RAM
EEPROM
11 Alternate command terminator
Terminate 0 = None (COS Only), 1-4 = A-D, 5 = *, 6 = #,
7 = Inter-digit timer, 8 = Min 1 digit cmds, 9 = Min 2 digit
cmds, 10 = Min 3 digit cmds, 11 = Min 4 digit cmds, 12 =
Min 5 digit cmds, 13 = Min 6 digit cmds, 14 = Min 7 digit
cmds, 15 = Min 8 digit cmds
11 11 [Terminate] 7
Inter-digit
RAM
EEPROM
12 Transmit audio output adjust
Adj. = 0 to 63 or * up one count, # down one count 12 12 [Adj] 31
RAM
EEPROM
13 DAC output
DAC 1 & 2, Output 0-255 (0 = 0 volts, 255 = 5 volts) 13 13 [DAC] [Output] 0 RAM
EEPROM