Panasonic AJ-HD150FE Displaying the Hours Meter information, Item No Description

Error messages

Displaying the “HOURS METER” information

Turn the search dial to move the cursor ( * ). The description for the item where the cursor is located is shown as a superimposed display.

Item No.	Item	Description
H00	OPERATION	Displays the time that the power has been supplied in one-hour units.
H01	DRUM RUN	Displays the time that the drum has been rotating in one-hour units.
H02	TAPE RUN	Displays the time that the tape has been running during FF, REW, PLAY, SEARCH (JOG,
		VAR, SHTL), REC, and EDIT modes (except for STILL in the JOG, VAR or SHTL mode) in
		one-hour units.
H03	THREADING	The number of times for threading/unthreading is displayed in single units.
H11	DRUM RUN r	Displays the time that the drum has been rotating in one-hour units. (Can be reset)
H12	TAPE RUN r	Displays the time that the tape has been running during FF, REW, PLAY, SEARCH (JOG,
		VAR, SHTL), REC, and EDIT modes (except for STILL in the JOG, VAR or SHTL mode) in
		one-hour units. (Can be reset)
H13	THREADING r	The number of times for threading/unthreading is displayed in single units. (Can be reset)
H30	POWER ON	The number of times the power has been turned on is displayed in single units.

<Notes>

•The resettable items in the “HOURS METER” information are reset by the shop when performing maintenance or other work.

•The search buttons and the search dial cannot be operated while the DIAG menu is displayed.

If “T&S&M” is selected in the setup menu No. 006 (DISPLAY SEL), a message appears in the mode display whenever a warning or error occurs. When multiple events occur, the event with the highest priority is displayed.

Priority	Display	Description
High	Error messages	When an abnormal operation is detected in this unit, the AUTO OFF lamp lights up
	(See error message table)	and an error message is displayed.
	INT SG	When INT SG is selected in setup menu No.600 (VIDEO IN SEL) or No.700
		(AUDIO IN SEL), pressing REC button or EDIT button causes the display to be
		given for 2 sec. from the beginning (EE mode).
		Similarly in edit mode, the display will be given for 2 sec. from the beginning.
	NO INPUT	In case of no input signal at the connector selected by setup menu No.600 (VIDEO IN SEL)
		or No.700 (AUDIO IN SEL) except analogue audio, pressing REC button or EDIT button
		causes the display to be given for 2 sec. from the beginning (EE mode).
		Similarly in edit mode, the display will be given for 2 sec. from the beginning.
	Warning messages	When a warning occurs in this unit, the warning lamp lights up and a warning
	(See warning message	message is displayed. When multiple warnings occur, the warning with the highest
Low	table)	priority is displayed.

Warning messages

Priority

Monitor display

Description

VTR operation

High

FAN STOP

This is displayed when the fan motor stops.

Operation continues

NO RF

This appears when a blank part of the tape lasting for 1

or more

seconds has been detected during playback.

When all the following conditions have been met, it will be recognized

Operation continues

as a blank part.

· When no signals are output from any of the heads

· When the playback data cannot be read

· When CTL is not present

SERVO NOT

This

is

displayed

when

the servo is

not

locked for three

or more

Operation continues

LOCKED

seconds during playback, recording, or editing.

LOW RF

This is displayed when envelope levels approximately 1/3

that

of

normal levels are detected for more than one second

during

Operation continues

playback, recording, or editing.

HIGH ERROR

This

is

displayed

when

the error

rate

increases and correction/

Operation continues

Low

RATE

interpolation is performed on either the video or audio playback signal.

– 105 –