Panasonic AJ-HD150FE operating instructions Time Code

Setup menus

USER menu

<TIME CODE>

	Item		Setting
							Description
No.	Superimposed		No.	Superimposed
	display				display
500	VITC		0000			BLANK	For selecting whether to output the VITC signal at the posi-
	BLANK		0001			THRU	tions selected by setup menu items No. 501 (VITC POS-1)
							and No. 502 (VITC POS-2).
							0: VITC signals are not output.
							1: VITC signals are output.
							<Note>
							This setting takes effect only with the SD output.
501	VITC		0000			10L	This sets the position where the VITC signal is to be inserted.
	POS-1		:		:		<Notes>
			0006			16L	• The same line as the one used for the setup menu item
			:		:		No. 502 (VITC POS-2) setting cannot be set.
			.0010			20L	• This setting takes effect only with the SD output.
502	VITC		0000			10L	This sets the position where the VITC signal is to be inserted.
	POS-2		:		:		<Notes>
			0008			18L	• The same line as the one used for the setup menu item
			:		:		No. 501 (VITC POS-1) setting cannot be set.
			0010			20L	• This setting takes effect only with the SD output.
503	REGEN		0000			REGEN	This sets the synchronization of the internal time code
			0001			PRE	generator.
							0: The time code reader is synchronized with the time code
							read from the tape.
							1: What the time code generator will be synchronized with can
							be preset using either the operation panel controls or the
							remote controller.
504	RUN MODE		0000			REC	This sets the operation mode in which the time code of the
			0001			FREE	internal time code generator is to advance.
							0: The time code advances only during recording.
							1: It advances while the power is on regardless of the mode
							which has been established.
505	TCG		0000			TC&UB	This selects the signal to be regenerated when the TCG (time
	REGEN		0001			TC	code generator) is in the REGEN mode.
			0002			UB	0: Both the time code and user’s bit are regenerated.
							1: Only the time code is regenerated.
							2: Only the user’s bit is regenerated.
506	REGEN		0000			AS&IN	This selects whether the time code is to be regenerated during
	MODE	0001			ASSEM		automatic editing using the unit’s control panel.
		0002				INSRT	0: The time code is regenerated with assemble or insert
		0003				MANU	editing.
							1: The time code is regenerated with assemble editing.
							2: The time code is regenerated with insert editing.
							3: The setup menu item No.503 (REGEN) setting is followed.
507	EXT TC SEL	0000				L TC	This selects the time code in use of external time code.
		0001				SLTC	0: LTC of TIME CODE IN terminal is used.
		0002				SVITC	1: LTC information applied to serial signal is used.
							2: VITC information applied to serial signal is used.
508	BINARY	0000				000	This sets the usage status of the user bit of the time code
	GP	0001				001	generated by the TCG.
		0002			010		0: NOT SPECIFIED (character set not specified)
		0003			011		1: ISO CHARACTER (8 bits character set based on ISO646,
		0004			100		ISO2022)
		0005			101		2: UNASSIGNED 1 (undefined)
		0006			110		3: UNASSIGNED 2 (undefined)
		0007			111		4: UNASSIGNED 3 (undefined)
							5: PAGE/LINE
							6: UNASSIGNED 4 (undefined)
							7: UNASSIGNED 5 (undefined)

The underline on the setting item denotes the initial setting.

– 82 –