Installation, Transportation bracket removal | Panasonic CQ-VA707N

Installation

E

N Preparation

G

L

I

S¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your

Hhands and fingers.

47¡We strongly recommend you to wear gloves for installation work to protect yourself from injuries.

¡Before installation, check the radio operation with
antenna and speakers.
¡Disconnect the cable from the negative (–) battery
terminal (see caution below).
¡The unit should be installed in a horizontal posi-
tion with the front end up at a convenient angle,	30° or less
but not more than 30°.

Caution: Do not disconnect the battery terminals of a car with trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts.

Dashboard Installation

Installation Opening

The unit can be installed in any dashboard having an opening as shown at
right. The dashboard should be 4.5 mm - 6 mm thick in order to be able to
support the unit.	182 mm

53 mm

❏Transportation bracket removal

Be sure to remove the transportation brackets before use (installation). Use screws (5 mmφ x 6 mm) with washers for installation.

Be careful not to lose these screws.

Binding-Head

Screws

(5 mmφ x 6 mm)

Transportation

Bracket

Display Unit

Transportation

Bracket

Binding-Head

Screws

(5 mmφ x 6 mm)

50

CQ-VA707N

Image 49

Panasonic CQ-VA707N operating instructions Transportation bracket removal, But not more than, Installation Opening

Contents

Panasonic Contents ¡ID code setup Features¡7-inch wide LCD color display When Driving PrecautionsID Code Battery Insertion Remote Control PreparationBattery Notes Insert the battery Names of Controls Remote Control Unit Display Unit Remote Remote Control Sensor Front Front See pages 55 to 61 about electrical connections Control Unit Power off Power onHow to Open and Raise the Display Before Use Slip part in the upper half of it, Adjust its lateral angle Display Unit Lateral Angle AdjustmentTilt Slide Retracting the Display Folding Down the Display Temporarily Menu Tree Using the Menu/Menu Control Main Menu Setting/Adjusting Menu Monitor Position TILT/SLIDE User SettingsSlide Tilt Press or to Clock Mode Clock Setting ClockClock Display Select Display On Clock display is on OFF Clock display is off Navigation Set Up Navi SET UP How to enter your ID code For the first time ID Code ID-CODE Setting How to change your ID code Loud beep sounds for 10 seconds ID Code Input Navi Input Selection Input SelectCamera OFF Panasonic Car Navigation System CN-DV2000EN Connection exampleOther corporations’ car navigation sys- tem RGB connection TV Tuner CY-TN1500PEN Rear View CameraOthers equipment such as video camera Connect to a video input of VTR1 or VTR2 RGB Example of connecting to two or more productsVTR2 View Camera a car navigation system is TV Tuner CY-TN1500PEN and RearCar Navigation Merits when ACC is activated If your car has no ACC, be sure to use a default, ACC OFFACC Selection ACC Tone Bass/Treble Sound SettingsBalance/Fader Beep LoudnessMenu Press or to select Dimmer Screen AdjustmentContrast Color BrightnessTint Tint Changing the Operation Mode VolumeOperation General Mute Displaying the Car Navigation Screen Radio Basics Tuning in to a Preset Station Station PresetManual Station Preset Auto Station Preset Traffic Announcements Radio Data System RDSProgram Type Display Emergency Announcement Reception AF1 Alternative Frequency AF Region on Region OFF Region Setting TA Volume Seek tuning and auto preset memoryMuting in TA Mode Traffic Announcement TA UME TA Volume TA Volume PTY Language Program Type PTY DisplayPTY Selection Speech → Music PTY Preset Change PTY PresetPTY Search Press Enter to set the PTY language PTY Language Starting the CD Changer CD Changer BasicsTitle Display Changer Control Disc Random Only for remote control Track Random Only for remote controlTrack Selection Track Search Disc Scan Only for remote control Track Scan Only for remote controlTrack Repeat Only for remote control Disc Repeat Only for remote control Dual CD Changer Only for remote control Press Mode to change to VTR1 mode or VTR2 mode as follows VTR ModeExample of VTR1 mode Alarm indicator Auxiliary Normal Aspect Ratio for VTR ModeFull Zoom Installation Opening InstallationTransportation bracket removal But not more than Installation Precautions Secure the rear of the unit Installation Procedures Diagram Qty Using the Rear Support Strap u Mounting Example Mounting the Control Unit Basic System Connecting the Power Source Electrical Connections Rear Example 2 Advanced System Electrical ConnectionsAmplifiers CY-M9054EN and CY-M7052EN CQ-VA707N You need the optional dual changer control unit CA-CD55EN Example 3 Connection with two CD Changers CX-DP9061EN Connecting the Reverse Cord Connecting the Parking Brake Connection LeadParking brake switch position Varies with the vehicle model Maintenance Troubleshooting Error Display Message CD Changer Troubleshooting TipsPower Display Possible Cause Problem Probable Solution Display General VTR, AV, Camera Video, Video Camera, Rear View Camera Remote ControlRadio Kitchen cleanser diluted with water Clean dirt by wiping lightly with a soft clothWill result in discoloration or removal of the paint Damage the surface of the unit Specifications Central P.O. Box 288, Osaka 530-91, Japan