Update Firmware | Panasonic KX-HCM8 specification

Operating Instructions

3.5.14Update Firmware

Update Firmware window allows the user to install the latest version of the Network Camera internal operating system. In most cases, this will never be necessary. Changes may be necessary to accommodate new operating systems or new web browsers that are not shown on page 10. In those cases, Update Firmware would be available from the Network Camera Technical Support Site at http://panasonic.co.jp/pcc/en/. Check the current firmware version on Setup Page on page 46.

Notes

•Do not turn off the power during Update Firmware. If the operation of Update Firmware is stopped, refer to page 108.

•Buffered Images are erased when performing Update Firmware.

1.

2.

Download the proper firmware from the Network Camera Technical Support Site mentioned above.

If Network Camera is accessible from the Internet, temporarily disable access and connect Network Camera to the PC as the following figure. This will eliminate any interruption during the Update Firmware.

Without Ethernet hub, you should use category 5 cross cable.

or

Ethernet hub

Category 5 straight cable

or

Broadband Router

Note

When Network Camera uses the DHCP function, change the Internet connection from DHCP to Static in Network window. Refer to page 50 for the network parameters.

3.Access Setup Page by entering "http://IP Address (or URL):Port No./ config.html" on the web browser and press [Enter].

•When port number is 80 (default), you do not need to enter port number.

82

Image 82

Panasonic KX-HCM8 operating instructions Update Firmware

Contents

Network Camera Introduction For operation assistance Call Trademarks Network Camera Memo Important Safety Instructions Table of Contents Technical Guides Specification and TroubleshootingIndex 115 Section Main Features Getting to Know Network Camera Authentication Update FirmwareMulti-Language Display System Requirements Authentication-System Security Feature Authentication window Included Accessories Setup CD-ROM Camera Feature Locations Front View Rear View Bottom View Network Camera Setup Installation Procedure Network Camera Configuration Type Type 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Network Parameters Table Network Camera Configuration Type Port NoDefault IP address How to refer the network parameters from the PC Enter winipcfg and click OK. IP configuration window appears Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top If Top Page does not appear Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Multi-Camera Motion JpegSingle Camera Help ActiveX Controls Single Camera Screen Using Operation Bar Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Primary ViewerClicking Start Capture Secondary Multi-Camera Screen Setup Setup Go to Top AdministratorCamera Setup Name/Time This option first. Refer to Entered. If any operational issues are changed, tryFunctions of Network Camera Go to Top Network Instructions for the data fields Enter only the number Dhcp Ddns File size of the image Name Name/TimeCamera Date Auto AdjustmentTime Changed AM/PM or 24H Time Zone Security Administrator Click Security Administrator on Setup For Setup Password EnableRetype Click Security General User on Setup Security General User Delete or Modify User ID ListNew User Top View Image Image ResolutionInstructions for the data fields Top 160 x Image Quality Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Sets the image resolution and image quality Alarm enable conditionActive Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Fixed Indoor Power LineWhite Balance Fixed Multi-Camera URL * 1 or Host Enable check boxIP Address or Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Restart Click Restart Now Update Firmware Click Update Firmware Operating Instructions Reset to Factory Default Click Reset to Factory Default on Setup Click Execute Technical Guides Flexible Stand Mounting MountingTripod Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor Input Circuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character set Displayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Default Settings List Items Factory Default Indispensable setting Value Network Image Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Network Camera Specifications Description SpecificationsOther Specification Description SMTP, FTP About Network Camera Setup TroubleshootingProblem Cause and Remedy For Indicator Control window ISP Network window on About Network Camera Setup Problem Cause and Remedy About Top View Image screen View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP For product service When you ship the product