Option settings

Press the

F or G button on the

 

projector

or remote control unit to

 

select an

item, then press the

I or

Hbutton to change the setting.

OPTION

 

 

 

OSD

OFF

ON

 

 

 

 

 

AUTO SEARCH

OFF

ON

 

 

 

AUTO SIGNAL

OFF

ON

 

 

 

RGB2 SELECT

INPUT

OUTPUT

 

 

 

RGB/YPBPR

RGB

YPBPR

 

 

 

VGA60/480p

VGA60

480p

 

 

 

BACK COLOR

BLUE

BLACK

 

 

 

CINEMA REALITY

OFF

ON

 

 

 

NEXT PAGE @

 

 

 

 

 

 

 

 

 

 

 

 

 

SELECT:[^][@]

 

 

 

 

 

 

 

 

 

 

 

 

 

ADJUST:[{][}]

 

ESC:[MENU]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OPTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PREVIOUS PAGE ^

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FRONT/REAR

FRONT

REAR

 

 

 

 

 

DESK/CEILING

DESK

CEILING

 

 

 

FAN CONTROL

STANDARD

HIGH

 

 

 

LAMP POWER

LOW

HIGH

 

 

 

LAMP RUN TIME

 

 

 

 

 

10 H

 

 

 

FUNC1

MUTE

KEYSTONE

 

 

 

CONTROL KEY

OFF

ON

 

 

 

SET ID

 

 

 

ALL

 

 

 

AUTO POWER OFF

 

 

 

DISABLE

 

 

 

SELECT:[^][@]

 

ENTER:[ENTER]

 

 

 

ADJUST:[{][}]

 

ESC:[MENU]

OSD

ON

The signal name is displayed in the top-right corner of the screen when the input signal is changed.

OFF

Use this setting when you do not want the signal name to be displayed.

NOTE:

BThe setting for “TV-SYSTEM” will also be displayed when an

S-VIDEO/

VIDEO signal is being

input.

 

AUTO SEARCH

ON

The input signal will be detected and selected automatically when the input select (RGB, VIDEO) buttons are pressed for a few seconds. (page 14)

OFF

“AUTO SEARCH” is disabled.

NOTE:

B“AUTO SEARCH” will not function when the input signal is being projected.

AUTO SIGNALThis should normally be set to “ON”.

ON

“AUTO SETUP” will be carried out automatically when the input signal is changed.

OFF

“AUTO SETUP” will not function when the input signal is changed.

RGB2 SELECT

This setting is used to select the function of the RGB2 IN/RGB OUT connector.

When set to “OUTPUT”, the selected input signal (RGB1 or RGB3) will be output.

RGB/YP B P R

This setting is valid when 480i, 576i, 480p, 576p, 1 080/60i, 1 080/50i and 720/60p signals are being input.

Select the setting in accordance with the input signal.

“RGB/YP B P R ” is displayed when the RGB1 IN, RGB2 IN or RGB3 IN connector has a signal being input.

Adjustments and settings

E NGLISH

-47