Creating a Login, Administer Logins | Paradyne HOTWIREt 7984

Security

Access level is also used to control access via Telnet. If the Telnet Session

Access Level is set to Administrator (see Table A-5,Telnet Session Options), a

Login ID with an Operator access level is not permitted access.

Creating a Login

Logins apply to the terminal directory connected to the communication port or

Telnet access directly to the ATI of the 7984 Standalone Termination Unit.

Six login ID/password combinations are available. Each Login ID and Password must be unique and include an access level.

"Procedure

1.To create a login record, follow this menu selection sequence: Main Menu → Control → Administer Logins

main/control/admin_logins		Hotwire
		Model: 7984
ADMINISTER LOGINS		Page 1 of x
Login ID:	newuser
Access Level:	Administrator

±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±

ESC for previous menu	MainMenu	Exit
Save	New	Del

2. Select New and press Enter. The Login Entry screen is displayed.

main/control/admin_loginss/entry				Hotwire
				Model: 7984
LOGIN ENTRY
Login ID:	newuser2
Password:	es342
Re-enter Password: es342

Access Level:	Administrator

WARNING

New logins will not become permanent until saved through the ªADMINISTER LOGINSº screen!

±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit Save

7-2

February 1999

7984-A2-GB20-10

Image 74

Paradyne HOTWIREt 7984 manual Creating a Login, Administer Logins, Login Entry

Contents

HOTWIRE Hdsl Standalone Termination Unit Copyright E 1999 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps Document Summary About This GuideDocument Purpose and Intended Audience Product-Related Documents Hdsl Overview About the Hotwire Standalone Termination UnitHotwire 7984 Termination Unit Features About the Hotwire 7984 Standalone Termination Unit Network Configuration CO Site Front Panel LED Status Indicators Rear Panel Interface Connections Snmp Trap Support Snmp Management CapabilitiesManagement Information Base MIB Support Network About the Hotwire 7984 Standalone Termination Unit Communication Port Settings Using the Asynchronous Terminal InterfaceUser Interface Access Login Initiating an ATI Session Area SelectScreen Function Main Status Test Keys Screen Work AreasInput Field Value Choices Messages Press Navigating the ScreensKeyboard Keys Screen Function Keys For the screen function Select Press Enter to Switching Between Screen Work Areas Example Ending an ATI Session Using the Asynchronous Terminal Interface Initial Startup and Configuration Overview Connecting Power to the Unit +24 Vdc Power Supply Pinouts Connecting to the Network Connecting to a System Terminal Identity Entering Identity InformationMain Menu → Control → Change Procedure Configuration Option Area Configuration Option Set Choosing a Configuration ModeConfiguring the Unit Using the Configuration Menus Configuring the Unit Using the Internal Switches Handling Precautions for STATIC-SENSITIVE Devices Switchpack Locations Switchpack S1 & S2 OFF = Switchpacks Disabled Switchpack DefinitionsSwitchpack S1 Definitions Switch # Allows you to OFF = Internal Clock Switchpack S2 Definitions Switch # Allows you to Load Configuration from Accessing and Displaying Configuration OptionsMain Menu → Configuration Load Configuration From If you select Then Main Menu → Configuration → Default Factory Configuration Edit/DisplayMain Menu → Configuration → Current Configuration Select To Access To Configure Configuration Loader Main Menu → Configuration → Configuration Loader Completed successfully Saving Configuration Options Save Configuration Download Code Download CodeMain Menu → Control → Download Code DSL Monitoring the Unit What to Monitor System and Test Status Health and Status SELF-TEST Results Viewing System and Test StatusMain Menu → Status → System and Test Status Health and Status Yyyyyyyy Call your service Self-Test Results Test Status Test Status Messages Meaning Network Error Statistics Viewing Network Error StatisticsMain Menu → Status → Performance → Network Error Statistics Viewing Network Performance Statistics This Field Contains This Field Contains Viewing DSX-1 Performance Statistics DSX-1 Performance Statistics This Field Contains General Viewing 7984 Standalone Termination Unit LEDsMain Menu → Status → Display LEDs LED is Indicating Standalone Termination Unit LEDsType Monitoring the Unit Main Menu → TestingAccessing the Test Menu Test Network & DSX Tests Running Network TestsMain Menu → Test → Network & DSX Tests Line Loopback T1 to V.35 Repeater Loopback Repeater LoopbackT1 to T1 Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Main Menu → Test → Device Tests Device TestsLamp Test Device Tests Telco-Initiated Line Loopback Ending an Active TestTelco-Initiated Tests Telco-Initiated Payload Loopback Telco-Initiated Remote Line Loopback Messages and Troubleshooting Configuring Snmp Traps Snmp Traps Options Device Messages Device Messages 1 What Message Indicates What To Do Device Messages 2 What Message Indicates What To Do Troubleshooting Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting 2 Symptom Possible Cause Solutions Tables ATI Access LevelsSecurity Login Entry Creating a LoginAdminister Logins On the Login Entry screen, for Enter Assigning Snmp Community Names and Access Types Deleting a LoginControlling Snmp Access Resetting the Termination Units COM Port or Factory Defaults Main Menu → Configuration → Management → Security Menu If entering yes to prompt Then IP Addressing Selecting an IP Addressing Scheme IP Addressing Example Peer IP Address Assignments Configuration Option Tables Configuration Options in , Initial Startup and Configuration Table A-1. Network Interface Options 1 Main Menu → Configuration → Current Configuration →Network Interface Options Menu Circuit Identifier DSL Line Rate Possible Settings 400, 528, 784, 1040Table A-1. Network Interface Options 2 Table A-2. DSX-1 Interface Options 1 Main Menu → Configuration → Load Configuration From →DSX-1 Interface Options Port Status Table A-2. DSX-1 Interface Options 2 System Options Menu DSL ModeTest Timeout Table A-3. System Options 1 Remote Telco Loopback Table A-3. System Options 2Telco Initiated Loopback Table A-4. Communication Port Options 1 Port Type Possible Settings Asynchronous, SynchronousCommunication Port Port Use Table A-4. Communication Port Options 2 Inactivity Timeout Terminal Use Only Login Required Terminal Use OnlyPort Access Level Terminal Use Only Table A-4. Communication Port Options 3 Telnet Session Options Management and Communication Options MenuTelnet Session Options Table A-5. Telnet Session Options PPP Communication Protocol OptionsCommunication Protocol Options Default Network Destination Node IP Address Possible Settings 000.000.000.000 ±Node Subnet Mask Possible Settings 000.000.000.000 ± Table A-6. Communication Protocol Options 1 Table A-6. Communication Protocol Options 2 Communication Port Link Protocol Table A-7. General Snmp Management Options 1 Community Name Possible Settings Ascii text field, PublicGeneral Snmp Management Options Snmp Management Table A-7. General Snmp Management Options 2 Name 1 AccessName 2 Access NMS IP Validation Snmp NMS Security OptionsTable A-8. Snmp NMS Security Options 1 Number of Managers Access Level Table A-8. Snmp NMS Security Options 2 Snmp Traps Snmp Traps OptionsTable A-9. Snmp Traps Options 1 Number of Trap Managers Enterprise Specific Traps Table A-9. Snmp Traps Options 2NMS n Destination Link Trap Interfaces Link Traps Possible Settings Disable, Up, Down, BothTable A-9. Snmp Traps Options 3 Snmp Traps AuthenticationFailureStandards Compliance for Snmp Traps WarmStart LinkUp and linkDown LinkUp/Down Variable-Bindings Enterprise-Specific Traps DSX Cables and Pin Assignments T1 Network Interface Position Modular Plug Unkeyed DB15 Socket DSL Network Interface Cable Table C-2. DSL Network Interface ConnectorSignal Pin Number Figure C-3. COM Port-to-PC Cable Feature Number 7900-F1-507 COM Port Interface Cable Table C-3. COM Port Connector J6 Signal Direction Pin Number Table C-4. DC Power Connector Signal Pin Number Power Input ConnectorOptional Power Cable Technical Specifications Specifications Criteria Technical Specifications Bridged tap Glossary511 COM port Frame relay Factory defaultsEthernet 703 Loopback ResetIP address Router SES Telnet Index IN-1 IN-2 IN-3 IN-4