Repeater Loopback | Paradyne HOTWIREt 7984 manual

Testing

Repeater Loopback

Repeater Loopback (RLB) loops the signal being sent from the data port back to the data port.

DSL

Port

AIS

CAP	CAP	T1
		LIU	DSX-1
		LIU	Port
			Port
Transceiver	Framer	Framer
			99-16111-01

T1 to T1 Repeater Loopback
CAP	CAP	T1
DSL		LIU	DSX-1
Port		LIU	Port
Port			Port
Transceiver	Framer	Framer
			98-16111

T1 to V.35 Repeater Loopback

"Procedure

To run a Repeater Loopback:

1.Position the cursor at the Start command next to Repeater Loopback on the Network Tests screen.

2.Press Enter.

The Start command is changed to Stop.

3.To manually stop the test, verify that the cursor is positioned at the Stop command.

4.Press Enter.

A Repeater Loopback cannot be started when any other Loopback test is in progress.

NOTE:

Activating the Repeater Loopback test causes the EOC to be lost to the remote unit.

5-4

February 1999

7984-A2-GB20-10

Image 60

Paradyne HOTWIREt 7984 manual T1 to T1 Repeater Loopback, T1 to V.35 Repeater Loopback

Contents

HOTWIRE Hdsl Standalone Termination Unit Copyright E 1999 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related Documents About the Hotwire Standalone Termination Unit Hotwire 7984 Termination Unit FeaturesHdsl Overview About the Hotwire 7984 Standalone Termination Unit Network Configuration CO Site Front Panel LED Status Indicators Rear Panel Interface Connections Snmp Management Capabilities Management Information Base MIB SupportSnmp Trap Support Network About the Hotwire 7984 Standalone Termination Unit Using the Asynchronous Terminal Interface User Interface AccessCommunication Port Settings Login Initiating an ATI Session Select ScreenArea Function Main Status Test Screen Work Areas InputKeys Field Value Choices Messages Navigating the Screens Keyboard KeysPress Screen Function Keys For the screen function Select Press Enter to Switching Between Screen Work Areas Example Ending an ATI Session Using the Asynchronous Terminal Interface Initial Startup and Configuration Overview Connecting Power to the Unit +24 Vdc Power Supply Pinouts Connecting to the Network Connecting to a System Terminal Entering Identity Information Main Menu → Control → ChangeIdentity Procedure Choosing a Configuration Mode Configuring the Unit Using the Configuration MenusConfiguration Option Area Configuration Option Set Configuring the Unit Using the Internal Switches Handling Precautions for STATIC-SENSITIVE Devices Switchpack Locations Switchpack S1 & S2 Switchpack Definitions Switchpack S1 Definitions Switch # Allows you toOFF = Switchpacks Disabled OFF = Internal Clock Switchpack S2 Definitions Switch # Allows you to Accessing and Displaying Configuration Options Main Menu → Configuration Load Configuration FromLoad Configuration from If you select Then Configuration Edit/Display Main Menu → Configuration → Current ConfigurationMain Menu → Configuration → Default Factory Select To Access To Configure Configuration Loader Main Menu → Configuration → Configuration Loader Completed successfully Saving Configuration Options Save Configuration Download Code Main Menu → Control → Download CodeDownload Code DSL Monitoring the Unit What to Monitor Viewing System and Test Status Main Menu → Status → System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Yyyyyyyy Call your service Self-Test Results Test Status Test Status Messages Meaning Viewing Network Error Statistics Main Menu → Status → Performance → Network Error StatisticsNetwork Error Statistics Viewing Network Performance Statistics This Field Contains This Field Contains Viewing DSX-1 Performance Statistics DSX-1 Performance Statistics This Field Contains Viewing 7984 Standalone Termination Unit LEDs Main Menu → Status → Display LEDsGeneral Standalone Termination Unit LEDs TypeLED is Indicating Monitoring the Unit Testing Accessing the Test MenuMain Menu → Test Running Network Tests Main Menu → Test → Network & DSX TestsNetwork & DSX Tests Line Loopback Repeater Loopback T1 to T1 Repeater LoopbackT1 to V.35 Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Device Tests Lamp TestMain Menu → Test → Device Tests Device Tests Ending an Active Test Telco-Initiated TestsTelco-Initiated Line Loopback Telco-Initiated Payload Loopback Telco-Initiated Remote Line Loopback Messages and Troubleshooting Configuring Snmp Traps Snmp Traps Options Device Messages Device Messages 1 What Message Indicates What To Do Device Messages 2 What Message Indicates What To Do Troubleshooting Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting 2 Symptom Possible Cause Solutions ATI Access Levels SecurityTables Creating a Login Administer LoginsLogin Entry On the Login Entry screen, for Enter Deleting a Login Controlling Snmp AccessAssigning Snmp Community Names and Access Types Resetting the Termination Units COM Port or Factory Defaults Main Menu → Configuration → Management → Security Menu If entering yes to prompt Then IP Addressing Selecting an IP Addressing Scheme IP Addressing Example Peer IP Address Assignments Configuration Option Tables Configuration Options in , Initial Startup and Configuration Main Menu → Configuration → Current Configuration → Network Interface Options MenuTable A-1. Network Interface Options 1 DSL Line Rate Possible Settings 400, 528, 784, 1040 Table A-1. Network Interface Options 2Circuit Identifier Main Menu → Configuration → Load Configuration From → DSX-1 Interface OptionsTable A-2. DSX-1 Interface Options 1 Port Status Table A-2. DSX-1 Interface Options 2 DSL Mode Test TimeoutSystem Options Menu Table A-3. System Options 1 Table A-3. System Options 2 Telco Initiated LoopbackRemote Telco Loopback Port Type Possible Settings Asynchronous, Synchronous Communication PortTable A-4. Communication Port Options 1 Port Use Table A-4. Communication Port Options 2 Login Required Terminal Use Only Port Access Level Terminal Use OnlyInactivity Timeout Terminal Use Only Table A-4. Communication Port Options 3 Management and Communication Options Menu Telnet Session OptionsTelnet Session Options Table A-5. Telnet Session Options Communication Protocol Options Communication Protocol OptionsPPP Node IP Address Possible Settings 000.000.000.000 ± Node Subnet Mask Possible Settings 000.000.000.000 ±Default Network Destination Table A-6. Communication Protocol Options 1 Table A-6. Communication Protocol Options 2 Communication Port Link Protocol Community Name Possible Settings Ascii text field, Public General Snmp Management OptionsTable A-7. General Snmp Management Options 1 Snmp Management Name 1 Access Name 2 AccessTable A-7. General Snmp Management Options 2 Snmp NMS Security Options Table A-8. Snmp NMS Security Options 1NMS IP Validation Number of Managers Access Level Table A-8. Snmp NMS Security Options 2 Snmp Traps Options Table A-9. Snmp Traps Options 1Snmp Traps Number of Trap Managers Table A-9. Snmp Traps Options 2 NMS n DestinationEnterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both Table A-9. Snmp Traps Options 3Link Trap Interfaces AuthenticationFailure Standards Compliance for Snmp TrapsSnmp Traps WarmStart LinkUp and linkDown LinkUp/Down Variable-Bindings Enterprise-Specific Traps DSX Cables and Pin Assignments T1 Network Interface Position Modular Plug Unkeyed DB15 Socket Table C-2. DSL Network Interface Connector Signal Pin NumberDSL Network Interface Cable Figure C-3. COM Port-to-PC Cable Feature Number 7900-F1-507 COM Port Interface Cable Table C-3. COM Port Connector J6 Signal Direction Pin Number Power Input Connector Optional Power CableTable C-4. DC Power Connector Signal Pin Number Technical Specifications Specifications Criteria Technical Specifications Glossary 511Bridged tap COM port Factory defaults EthernetFrame relay 703 Reset IP addressLoopback Router SES Telnet Index IN-1 IN-2 IN-3 IN-4