Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic manual Model 2292, Leased-Line Extenders over IP, Getting Started Guide

Models: 2292 2294

1 53

Download 53 pages 26.38 Kb

Page 1

Model 2292 & 2294

Model 2292 & 2294

Leased-Line Extenders over IP

Getting Started Guide

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail:support@patton.com

WWW: www.patton.com

:

Part Number: 07M2292-GS, Rev. A

Revised: April 13, 2009

Image 1

Patton electronic 2294 manual Model 2292, Leased-Line Extenders over IP, Getting Started Guide, Sales Ofﬁce +1 301

Contents

Leased-Line Extenders over IP Model 2292Getting Started Guide Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA tel +1 301 Summary Table of Contents Table of Contents Compliance information List of Figures List of Tables Audience About this guideStructure Note Calls attention to important information PrecautionsSafety when working with electricity General observations Preventing electrostatic discharge damageGeneral conventions Typographical conventions used in this documentModel 2292 & 2294 Series Getting Started Guide About this guideChapter 1 General information Chapter contentsSmartNode Series Leased-Line Extenders overview SmartNode 2292 and 2294 Leased-Line Extenders Ports descriptions Reset button behaviorThe SmartNode 2292 Series rear panel ports are described in table Figure 4. SmartNode 2292 and 2294 front panels Chapter contents Chapter 2 Applications overviewLeased-line extension Typical applicationChapter Hardware installationChapter contents Create a network diagram see section “Network information” on page Planning the installationVerify power source reliability see section “Power source” on page Task Installation checklistVeriﬁed by DatePower source Network DiagramSite log Network informationConnecting cables Installing the SmartNode extenderLocation and mounting requirements Mounting the SmartNode extenderFigure 7. Analog connection Installing an interface cable on the extender’s voice ports3 Hardware installation SignalInstalling the SmartNode extender 1.25A ResetNote Pins not listed are not used Installing the Ethernet cableInstalling the SmartNode extender 3 Hardware installation1.25A Reset Model 2292 & 2294 Series Getting Started GuideNote Do not connect the power cord to the power outlet at this time Connecting to external power sourcePower 3 Hardware installationInstalling the SmartNode extender VoIP LinkChapter contents Chapter 4 Getting started with the SmartNodeLoad configuration Introduction2. Modify configuration 3. Load configurationConﬁgure the IP address Power connection and default conﬁgurationConnect with the serial interface Login Chapter contents Chapter 5 LEDs status and monitoringPower Status LEDsDescription VoIP LinkChapter contents Chapter 6 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsOut-of-warranty service Contact informationRMA numbers Return for credit policyShipping instructions Patton Electronics CompanyChapter contents Appendix A Compliance informationCompliance SafetyCE Declaration of Conformity Chapter contents Appendix B SpeciﬁcationsQuality of Service Data ServicesVoice Signaling CapacityVoice Processing TemperatureManagement SystemChapter contents Appendix C CablingIntroduction Serial consoleNote See section “Console port” on page 51 for console port pin-outs Ethernet 10Base-T and 100Base-T Figure 20. Connecting an FXS device Analog FXSFigure 19. Ethernet straight-through Chapter contents Appendix D Port pin-outsEthernet 10Base-T and 100Base-T port Console portVoice port IntroductionChapter contents Appendix E Installation checklistIntroduction E Installation checklist