Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic 2292, 2294 manual Voice Processing, Management, System, Temperature, Humidity

Models: 2292 2294

1 53

Page 45

Model 2292 & 2294 Series Getting Started Guide	B • Specifications

Voice Processing

CODEC G.711 a-law/mu-law, G.723, G.729ab,

G.726, G.727. T.38 fax relay (9.6 k, 14.4k)

G.711 transparent fax and bypass

Management

Web/HTTP, CLI with local console and remote Telnet access

TFTP conﬁguration & ﬁrmware loading

SNMP MIB II and product MIB

Secure Mass provisioning for both ﬁrmware and unit conﬁguration

Built-in diagnostic tools (trace, debug, call generator)

System

CPU Motorola MPC875 @66MHz

Memory 32MB SDRAM/8MB Flash

Power 100–240 VAC (50/60Hz)

Power dissipation 4-8W, model dependent

Temperature

32–104°F (0–40°C)

Humidity

5–80%, non-condensing

Voice Processing

Page 45

Image 45

Patton electronic 2292, 2294 manual Voice Processing, Management, System, Temperature, Humidity

Contents

Leased-Line Extenders over IP Model 2292Getting Started Guide Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA tel +1 301 Summary Table of Contents Table of Contents Compliance information List of Figures List of Tables About this guide AudienceStructure Note Calls attention to important information PrecautionsSafety when working with electricity General observations Preventing electrostatic discharge damageGeneral conventions Typographical conventions used in this documentModel 2292 & 2294 Series Getting Started Guide About this guideChapter 1 General information Chapter contentsSmartNode Series Leased-Line Extenders overview SmartNode 2292 and 2294 Leased-Line Extenders Reset button behavior Ports descriptionsThe SmartNode 2292 Series rear panel ports are described in table Figure 4. SmartNode 2292 and 2294 front panels Chapter contents Chapter 2 Applications overviewLeased-line extension Typical applicationHardware installation ChapterChapter contents Planning the installation Create a network diagram see section “Network information” on pageVerify power source reliability see section “Power source” on page Task Installation checklistVeriﬁed by DatePower source Network DiagramSite log Network informationConnecting cables Installing the SmartNode extenderLocation and mounting requirements Mounting the SmartNode extenderFigure 7. Analog connection Installing an interface cable on the extender’s voice ports3 Hardware installation SignalInstalling the SmartNode extender 1.25A ResetNote Pins not listed are not used Installing the Ethernet cableInstalling the SmartNode extender 3 Hardware installation1.25A Reset Model 2292 & 2294 Series Getting Started GuideNote Do not connect the power cord to the power outlet at this time Connecting to external power sourcePower 3 Hardware installationInstalling the SmartNode extender VoIP LinkChapter contents Chapter 4 Getting started with the SmartNodeLoad configuration Introduction2. Modify configuration 3. Load configurationPower connection and default conﬁguration Conﬁgure the IP addressConnect with the serial interface Login Chapter contents Chapter 5 LEDs status and monitoringPower Status LEDsDescription VoIP LinkChapter contents Chapter 6 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsOut-of-warranty service Contact informationRMA numbers Return for credit policyShipping instructions Patton Electronics CompanyChapter contents Appendix A Compliance informationSafety ComplianceCE Declaration of Conformity Chapter contents Appendix B SpeciﬁcationsQuality of Service Data ServicesVoice Signaling CapacityVoice Processing TemperatureManagement SystemChapter contents Appendix C CablingSerial console IntroductionNote See section “Console port” on page 51 for console port pin-outs Ethernet 10Base-T and 100Base-T Analog FXS Figure 20. Connecting an FXS deviceFigure 19. Ethernet straight-through Chapter contents Appendix D Port pin-outsEthernet 10Base-T and 100Base-T port Console portVoice port IntroductionChapter contents Appendix E Installation checklistIntroduction E Installation checklist