Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic 2294, 2292 manual Installing an interface cable on the extender’s voice ports

Models: 2292 2294

1 53

Download 53 pages 26.38 Kb

Page 26

Installing an interface cable on the extender’s voice ports

Model 2292 & 2294 Series Getting Started Guide	3 • Hardware installation

Installing an interface cable on the extender’s voice ports

The SmartNode extender comes with at least two voice ports (see ﬁgure 6) located on the back of the extender. The voice ports are connected to analog devices via cables (see ﬁgure 7) terminated with RJ-11 connectors (see ﬁgure 9 and table 5 on page 27 for pin-out information).

Ethernet connectors	Voice ports

Ports

, 1.25A

Reset

ETH 0/1

ETH 0/0

,1.25A

Reset

ETH

0/1

ETH	0/0

Ports

Figure 6. Rear view showing location of Ethernet connectors and voice ports (SmartNode 2294 shown)

,1.25A

Reset

ETH	0/1

ETH	0/0

Ports

RJ-11, male		RJ-11, male

Figure 7. Analog connection

Installing the SmartNode extender

26

Image 26

Patton electronic 2294, 2292 manual Installing an interface cable on the extender’s voice ports, Analog connection

Contents

Getting Started Guide Model 2292Leased-Line Extenders over IP Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA tel +1 301 Summary Table of Contents Table of Contents Compliance information List of Figures List of Tables Structure About this guideAudience Precautions Note Calls attention to important informationSafety when working with electricity Preventing electrostatic discharge damage General observationsTypographical conventions used in this document General conventionsAbout this guide Model 2292 & 2294 Series Getting Started GuideChapter contents Chapter 1 General informationSmartNode Series Leased-Line Extenders overview SmartNode 2292 and 2294 Leased-Line Extenders The SmartNode 2292 Series rear panel ports are described in table Reset button behaviorPorts descriptions Figure 4. SmartNode 2292 and 2294 front panels Chapter 2 Applications overview Chapter contentsTypical application Leased-line extensionChapter contents Hardware installationChapter Verify power source reliability see section “Power source” on page Planning the installationCreate a network diagram see section “Network information” on page Veriﬁed by Installation checklistTask DateSite log Network DiagramPower source Network informationLocation and mounting requirements Installing the SmartNode extenderConnecting cables Mounting the SmartNode extenderInstalling an interface cable on the extender’s voice ports Figure 7. Analog connectionInstalling the SmartNode extender Signal3 Hardware installation 1.25A ResetInstalling the Ethernet cable Note Pins not listed are not used1.25A Reset 3 Hardware installationInstalling the SmartNode extender Model 2292 & 2294 Series Getting Started GuideConnecting to external power source Note Do not connect the power cord to the power outlet at this timeInstalling the SmartNode extender 3 Hardware installationPower VoIP LinkChapter 4 Getting started with the SmartNode Chapter contents2. Modify configuration IntroductionLoad configuration 3. Load configurationConnect with the serial interface Power connection and default conﬁgurationConﬁgure the IP address Login Chapter 5 LEDs status and monitoring Chapter contentsDescription Status LEDsPower VoIP LinkChapter 6 Contacting Patton for assistance Chapter contentsOut-of-warranty service Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Contact informationShipping instructions Return for credit policyRMA numbers Patton Electronics CompanyAppendix A Compliance information Chapter contentsCE Declaration of Conformity SafetyCompliance Appendix B Speciﬁcations Chapter contentsVoice Signaling Data ServicesQuality of Service CapacityManagement TemperatureVoice Processing SystemAppendix C Cabling Chapter contentsNote See section “Console port” on page 51 for console port pin-outs Serial consoleIntroduction Ethernet 10Base-T and 100Base-T Figure 19. Ethernet straight-through Analog FXSFigure 20. Connecting an FXS device Appendix D Port pin-outs Chapter contentsVoice port Console portEthernet 10Base-T and 100Base-T port IntroductionAppendix E Installation checklist Chapter contentsE Installation checklist Introduction