Press the EXIT/STATUS button. Program WAS COM | Philips VRX462

Timer Recording With the VCR Plus+ Programming System (cont’d) 41

5

Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. You cannot use the (Tape) SPEED button at this time.

ONE TIME PROGRAM

PROGRAM	2
CHANNEL	25
TIME ON	10:00 AM
TIME OFF	01:00 PM
REC SPEED	SLP

START DATE 07/10/97

THU.

PUSH 1=SP OR 2=SLP

TO END PUSH EXIT

6

Press the EXIT/STATUS button. PROGRAM WAS COM-

PLETED/PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen. (If PROGRAM NOT COMPLETED appears, begin again from step 1.) After five seconds, the on- screen display will disappear.

7

Press the POWER button to turn off the VCR. The VCR must be turned off for a timer recording to take place.

The TIMER light will appear on the display panel of the VCR when you turn off the VCR. The TIMER light and the Cassette-Inside light will flash if there is not a tape in the VCR.

The VCR must be off for a timer

recording to take place!

Make sure a tape is in the VCR.

7

6

5

CBL/DSS VCR TV

EJECT POWER MUTE

VOL F.ADV CHANNEL

PAUSE/STILL

PLAY

REWFF

VCR PLUS+	LIGHT
/ENTER	LIGHT
STOP
EXIT/STATUS MENU	CLEAR

1 2 3

4 5 6

7 8 9

100 0 GO-TO

REC/OTR	INDEX	MEMORY
	...
	...
	VAR. SLOW	TRACKING SKIP
SPEED VCR/TV SLOW		SEARCH

REMOTE LOCATOR

Helpful Hints

•To exit the VCR Plus+ programming system at any step, press the EXIT/STATUS button.

•PROGRAM NOT COMPLETED/ CLASH may appear on-screen for five seconds at step 6 if the timer recording you programmed overlaps with another timer recording. Then, the timer recording menu will appear. To cancel the overlapping timer recording, follow the steps on page 37.

Image 41

Philips VRX462, VRX442 warranty Press the EXIT/STATUS button. Program WAS COM

Contents

Video Cassette Recorder VRX442 VRX462 For Customer Use Dear Philips Magnavox product owner Introduction FeaturesSafety Precautions Table of Contents Putting Batteries in the Remote Control Before Using Your VCRUsing the Remote Control VCR Maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box Antenna Or Cable Hookups Without a Cable Box cont’d Hookups With a Cable Box/DSS Receiver Timer RecordingsRecording or Viewing a Scrambled or Unscrambled Channel Watching TV With the VCR Turned Off Recording One Channel/Watching Another Hookups With a Cable Box/DSS Receiver cont’dPlaying a Tape Antenna in Jack On back of TV Turn on the TV Turning on Your VCRVCR will come on and the menu shown below will appear Wait for the VCR to program channels Press the Menu button. The menu shown below will appear On the display panel of the VCR Press the Number 3 button to select Tuner SET UPProgramming Channels Press the VCR button Adding/Deleting ChannelsPress the Menu button to bring up the main menu display Press the Number 4 button to select ADD/DELETE CH Press the VCR button, then press the Menu button Setting the ClockPress the Number 3 button to select SET Manual Clock Press the EXIT/STATUS button Press the Number 4 button to select SET Time Zone Time Zone Selection Manual PBS Channel Selection Setting the Clock cont’d Press the EXIT/STATUS button. You will be prompted to Automatic PBS Channel SelectionTurn off the VCR Channels Press the EXIT/STATUS button to exit Daylight-Saving Time Selection Language Selection Press the Number 2 button to select VCR SET UPLanguage Press the Number 3 button to select Language Remote Control Buttons Stop Button Rame ADVance ButtonVCR PLUS+/ENTER Button EXIT/STATUS Button VRX462 Display Panel OTR Light Display Panel cont’dRemote Sensor Tape Speed Lights Memory Light Front Panel Rear Panel Find the code for your TV Repeat step Setting the Remote Control to Operate a TV Find the code for your Cable Box/DSS Receiver Repeat step Cable BOX/DSS Receiver Codes On-Screen Status Displays Press the Number 2 button to select on Screen ModeSound Program On Screen On and Counter Only modes Remote Locator When you find the remote control, point the remote atTo program the VCR to find its Remote control only Turn on the TV Insert a tape PlayingRead and follow the steps below to play a tape Recording VCR records in a preset volumeAppear on the display panel Stop. Details are on Starting an OTR One Touch RecordingStopping an OTR Tape Speed button. Details are on pages 36 Instructions carefully Recording One Channel/Watching AnotherPress the RECord/OTR button to start a recording Press the Number 1 button to select Program Timer RecordingSelect a once, daily or weekly recording Recording Then turn itself off Instructions continue onFollow the instructions in to set the recording’s stop time Tape Speeds Timer Recording cont’d Checking or Clearing Timer Recordings Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels 2page Examine the lists on Monday through Friday Select a ONCE, DAILY, or Weekly recording Press the EXIT/STATUS button. Program WAS COM Cable Box or DSS Receiver Controller Connecting the Controller Press the Menu button Timer recordingPress the Number 5 button to select SET Cable BOX Number 2 button to select NO. Use the Number buttons to Press the Menu button. Wait for a few secondsPress the Menu button or the EXIT/STATUS button Cable BOX Control is on will appear for five seconds Press the Number 6 button to select SET DSS Receiver Setting the Controller to Operate a DSS ReceiverPress the Number 1 button to set the DSS Receiver Controller to on Change the VCR Channels Press the Number 1 button to select YES To the Audio in Jack on VCR Rerecording Tape DuplicationVCR 1 will play your tape. Insert a prerecorded tape in VCR Index Search Receiving a Second Audio Program These features are not available with the VRX442Receiving a Stereo Broadcast Press the Number 1 button so that on appears beside Multi-Channel Television Sound System VRX462 only cont’d Hi-Fi Stereo Tape Playback VRX462 only Tape Counter Memory Using the Tape CounterMemory light will appear on the display panel Turned ON. Details are on To remove the Goto display, press the GO-TO button again Go-To Feature Repeat Playback Play mode Video Stabilizer Video Stabilizer Forward and Reverse Searching Playback OptionsViewing a Still Picture Viewing a Slow Motion Picture Automatic Operation Features Cable Box/DSS Receiver Output Channel channel 03 or Glossary Specifications Helpful Hints Helpful Hints cont’d Renewed Safety precautions Automatic With a stereo TV Playback Ac power cord Hi-fi stereo playback Rewind buttonOff mode Manually On mode Timer Supplied Accessories