INSTALLATION & OPERATIONAL SELV MANUAL
2.5 ELECTRICAL CONNECTIONS
It is advised that this appliance be connected to a power supply that is controlled by the ventilation system. This will prevent the appliance from being operated without the ventilation hood on.
If your appliance is single phase, it requires a hardwired, flexible conduit electrical connection, using conductors size appropriately for the power requirements listed below. Hardwired units require installation of a restraint device mounted to substantial building structure.
ELECTRICAL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| Nominal Amps Per Line (50/60 HZ) |
|
|
| |||||||
REQUIREMENTS |
| Single Phase (2 wire + ground) | 3 Phase (3 wire + ground) | 3 Phase "Y" (4 wire + ground) | ||||||||||||||
|
|
|
|
|
|
|
| |||||||||||
Model | KW/Hr | 2002 208 220 230 240 480 | 2002 208 220 230 240 480 | 346/200V | 380/220V | 400/230V | 415/240V | |||||||||||
SELV14X | 14 | 65 | 67 | 65 | 61 | 58 | 29 | 37 | 39 | 37 | 35 | 34 | 17 | 23 | 21 | 20 | 20 | |
SELV14TX | 14 | 65 | 67 | 65 | 61 | 58 | 29 | 37 | 39 | 37 | 35 | 34 | 17 | 23 | 21 | 20 | 20 | |
(both tanks) | ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
SELV14 | 17 | 79 | 82 | 78 | 74 | 71 | 36 | 46 | 48 | 45 | 43 | 41 | 21 | 28 | 26 | 25 | 24 | |
SELV14T | 17 | 79 | 82 | 78 | 74 | 71 | 36 | 46 | 48 | 45 | 43 | 41 | 21 | 28 | 26 | 25 | 24 | |
(both tanks) | ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
1.Each fryer requires it's own separate power supply connection. 2. 200V Units will operate at 92% of rated power. 3. Power supply for Basket Lifts and Filter motor is wired into the fryer's high voltage line terminal block, except for 480V. 480VAC line voltage requires a separate single phase service for the filter motor and Basket Lifts( If equipped) rated for 115V,8.0A for North America and
CAUTION
Connecting the appliance to the wrong power supply may damage the appliance and void the warranty
WARNING
This appliance must be connected to a power supply having the same voltage and phase as specified on the data plate located on the inside of the appliance door. DO NOT attempt to connect the appliance to an electrical supply other than that indicated on the data plate. Electrical connection should be performed by a qualified electrician
WARNING
The electrical connection used by this appliance must comply with local codes. If there are no local codes that apply, refer to the National Electrical Code (NEC), ANSI/NFPA 70 for installation in the US. In Canada, refer to CSA Standard C22.2 and local codes. In all other cases, refer to local and national codes and regulations.
The appliance must be grounded in accordance with local code, comply with the NEW and ANSI/NFPA No. 70 latest edition (for US and Canadian installations). In all other cases, refer To local and national codes and regulations. To comply with European requirements, European models are equipped with an
appliance is marked with the following universal symbol.
WARNING
A country approved all pole circuit breaker with a minimum open contact gap of 3mm must be used for proper installation. (CE countries)
WARNING
This equipment must be installed so that the plug (if used) is accessible unless other means for disconnection from the power supply (e.g: circuit breaker) is provided.
WARNING
If this appliance is permanently connected to fixed wiring, it must be connected by means of copper wires having a temperature rating of not less than 167°F (75°C), and have a local means of disconnection from all poles from the mains included in the fixed wiring in accordance with local codes.
WARNING
All power connection wiring for this appliance must be made in accordance with the wiring diagrams(s) located on the appliance.
CAUTION
Leakage current of this appliance may exceed 10 mA. When permanently connected, a high integrity protective system employing an RCD rated at 30 mA must be used with this appliance.
9 |
