System Diagram, Ethernet switch | Polycom 1725-36028-001 guide

System Diagram

SpectraLink 8000 Telephony Gateway Administration Guide

System Diagram

Access point

Wireless

Telephones

Access point

optional

Wireless

POS

CAT 5 cable

25 pair cable Multiple phone cables Phone cable

Device supplied

by Polycom

Administrative

computer

SpectraLink 8000

SVP Server

Ethernet switch

SpectraLink 8000

Telephony Gateway

SpectraLink 8000

Telephony Gateway

SpectraLink 8000

Telephony Gateway

SpectraLink 8000

Telephony Gateway

SpectraLink 8000

Telephony Gateway

Demarc block

PBX

desksets

Five SpectraLink 8000 Telephony Gateways with SpectraLink 8000 SVP Server example

14	PN: 1725-36028-001_T.doc

Image 14

Polycom 1725-36028-001 manual System Diagram, Ethernet switch

Contents

Utilizing SpectraLink Radio Protocol SRP Administration GuideSpectraLink 8000 Telephony Gateway Copyright Notice Trademark InformationPatent Information Contact Information Referenced Documents About This GuidePolycom Model Numbers SpectraLink 8000 SVP Server Administration Guide for SRP Deploying Enterprise-Grade Wi-Fi Telephony Customer SupportIcons and Conventions Best Practices Guide for Deploying SpectraLink 8020/8030 Wireless Installation and Configuration Steps ContentsTelephone Interface Configuration Site Preparation 7 SpectraLink 8000 Telephony Gateway Administration 5 Pre-Installation Verification6 Install SpectraLink 8000 Telephony Gateway 8 Connecting to the SpectraLink 8000 Telephony Telephone Line Configuration Network ConfigurationSet or Change Password Features Programming Menu Index Troubleshooting via the System Status MenuSafety Notices Wireless Device Planning Worksheet SpectraLink Overview System Architecture SpectraLink Voice Priority SVP and Quality of Service System Timing System Components SpectraLink Wireless TelephonesSystem Speed SpectraLink 8000 Telephony Gateway Router Access pointsEthernet switch Administrative computer SpectraLink 8000 SVP Server System Diagram Ethernet switch The Front Panel of the SpectraLink 8000 Telephony Gateway 4 Timing Master Installation and Configuration Steps ConditionalPage Site Preparation Required Materials Grounding materials per section below Grounding Instructions IP addressing LAN RequirementsNetwork infrastructure Location of SpectraLink 8000 Telephony Gateway and SVP Server Prepare Demarcation Demarc Blocks Telephone Interface ConfigurationModem administration SpectraLink 8000 Telephony Gateway Administration Guide Connect Telephone Lines to Demarc Blocks Install Telephone Demarc BlocksAssign and Program Telephone Ports Telephone Ports Two-wire analog or digital demarc block25 PAIR MALE CONNECTOR CABLE TO GATEWAY CONNECTOR A TX denotes data transmitted from the telephone system to the Gateway Four-wire digital demarc block Connector ATelephone Ports Telephone Four-wire digital demarc block Connector B25 PAIR MALE CONNECTOR CABLE TO GATEWAY CONNECTOR B Ports Check Components Pre-Installation VerificationVerify Pre-Installation Requirements Page Connector A is… Install SpectraLink 8000 Telephony GatewayMount to Rack or Wall To Mount Mount the SpectraLink 8000 Telephony Gateway to wall SafetyMount the SpectraLink 8000 Telephony Gateway to rack Grounding instructions All system units must be grounded to a protective earth by means of the grounding stud located on the rear panel. Refer to the illustration below for recommended continuity connection Mount Gateway Installing Multiple SpectraLink 8000 Telephony GatewaysInstall bonding straps Install IPC cables Connect SpectraLink 8000 Telephony Gateway to Demarc Blocks Connect powerConnect five or more SpectraLink 8000 Telephony Gateways Connect SpectraLink 8000 Telephony Gateway to LAN Status 1 should be blinking on each SpectraLink 8000 Telephony Gateway Page SpectraLink 8000 Telephony Gateway Administration Overview SpectraLink 8000 Telephony Gateway Administration Guide SpectraLink 8000 Telephony Gateway Configuration Sequence Send All 11. Perform AP coverage test per Certifying the Wireless Telephones Press Navigating through the Administration Console ScreensTo Perform this Function Page Connecting to the SpectraLink 8000 Telephony Gateway Connect via the Serial Port Select a SpectraLink 8000 Telephony Gateway to Administer If using a serial connection, only the SpectraLink 8000 Telephony Gateway that is connected via the serial cable is shown 5. Unplug the serial cable Connecting via Telnet Connecting via External Modem Configure modem internal settings US Robotics Sportster Connecting via Internal Modem Connect the modemPage Function Main MenuMenu Option Page Network Configuration Subnet Mask The network administrator must define the subnet mask correct setting from the DHCP server. The DHCP setting is only valid when the IP address is also acquired using DHCP Press Esc to return to the SpectraLink 8000 System menu Set or Change Password Page SpectraLink 8000 Telephony Gateway Configuration OAI hostname Valid entries Valid source location entries are Press Esc to return to the NetLink Wireless Telephone System menu Reset the SpectraLink 8000 Telephony Gateway Page Telephone Line Configuration Adding or Changing a Handset 3. Write the MAC address on the Wireless Planning Device Worksheet 3. Press D to delete the handset information Deleting a Handset2. Use the arrow keys to highlight the line to be deleted 4. Press Y to accept changesPage Features Programming Menu Page Feature Programming no Softkeys Interface Guide for your system Programming Digital PBX FeaturesProgramming Analog PBX Features 3. Type F to assign the FLASH function Programming the ADMIN Feature Menu Programming no softkeys To change the menu settings 4. Repeat for each menu as needed Page Softkey and Shortcut Key Programming Sample screen Scroll to remaining options Speakerphone softkey programming SpectraLink 8020/8030 only Softkey Label Software Maintenance Software Updates Updating Larger Systems Using FTPFTP procedure To transfer the software using FTP Updating Wireless Telephone Software Normal download messages Backup and Restore SpectraLink 8000 Telephony Gateway Configuration Download failure or recovery messages get config.bin gateway1.bin Troubleshooting via the System Status Menu Error Status Displays alarm and error message information Access Point Status D is day, HH is hours, MM is minutes, and SS is seconds Error StatusUnless noted otherwise, times are displayed using the format Alarm Error Description Reset = reset SpectraLink 8000 Telephony Gateway Alarm 1 SpectraLink Radio Protocol See Network Status section Network Status RX Broadcast The number of broadcast packets and bytes received Telephone Line Status Wireless Telephone Status WT MAC The MAC address of the handset Software Version Wireless Telephones per AP Wireless Device Planning WorksheetHost Switch Type Switch Port ID IP Address SpectraLink 8000 Telephony Gateway Administration Guide Safety Notices Page Index