Porter-Cable 4210, 4212 manual

Step 1 -

Step 7 -

Step 8 - Step 9 -

Unclamp the templet, slide it down, and center the last cut between the two angled fingers and reclamp (Fig. 11D).

Repeat STEPS 6 and 7 until the pins are cut across the entire board.

Remove the pin board and check the fit with the tailboard.

FITTING THE JOINT

Fitting the joint is identical to the previous section (Fig. 12A).

Fig. 11D

Fig. 12A

ALTERNATE METHOD

THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH

This alternate method may be more accurate for correctly cutting the tail and pin boards.

Clamp the tail and pin boards together with a 2" wide block (Fig. 13A). Step 2 - Use a square to align an edge of the tail and pin boards (Fig. 13B). Step 3 - Cut the pins and the tails as far as the template will allow (Fig. 13C).

Step 4 - Slide the template, aligning the last cut in between the fingers of the template (Fig. 13D). Step 5 - Repeat STEPS 3 and 4 until both boards are completely cut.

Fig. 13A

Fig. 13B

Fig. 13C

Fig. 13D

10

Image 10

Porter-Cable 4210, 4212 instruction manual Fitting the joint is identical to the previous section a

Contents

Supplementary Instructiondovetail JIG Manual Table of Contents Safety Guidelines Definitions Important Safety Instructions Replacement Parts Additional Safety RulesBackground Information Operation Miscellaneous Techniques Templates Mounted to Clamping Boards SetupTHROUGH-DOVETAILS with Clamping Boards Cutting the Pins Cutting the Tails THROUGH-DOVETAILS with Unlimited Board Width Fitting the Joint Set the router bit depth, using the pencil mark from Step Fitting the joint is identical to the previous section a HALF-BLIND Dovetails with Clamping Boards Blind Dovetails with Tail Boards Thicker than 7/8 Cutting the Joint Wood Grain Using a Router Table THROUGH-DOVETAIL Bits Alternate Router BitsTHROUGH-DOVETAIL BIT Combinations Readily Available HALF-BLIND Dovetail BIT Readily Available BOX Joint Bits Readily Available BOX Joint BitsDovetail Dado Bits HALF-BLIND Dovetails with Tail Boards Thicker than 7/8 Mitering the Pins Mitered THROUGH-DOVETAIL THROUGH-DOVETAIL, SKIPPED-PIN Method Mitering the Tails HALF-BLIND DOVETAIL, Skipped PIN Method Cutting the Pins SAW Kerf Allowance Method Cutting the Tails Fitting and Cutting the Joint Multiple Spacer MethodEND-TO-END Joints BOX END-TO-END Joints Drawers with Dovetail Dados Dovetail END-TO-END Joints Wooden Hinges Hinges with a Drilled Hole Hinges with ROUTER-MADE Grooves Hinges with ROUTER-MADE Grooves Angled Joints Setup with the Template Mounted to the Base of the JIGObtuse Angled Joints Setup with the Template Mounted to a Clamping Board Cutting the Tails Cutting the Pins Acute Angled Joints SLANTED-SIDE Joints COMPOUND-ANGLE Joints Setup Blade Tilt Angle Make Angled CUT Inlayed Through Dovetail Inlayed JointsMake the First Joint CUT OFF the Inlay Board Inlayed HALF-BLIND DovetailMake the Second Joint 100 13/128 050 042 028 014 Inlayed BOX Joint HALF-BLIND Dovetail Bits Tables of Commonly Available Router BIT SizesThrough Dovetail Router BIT Combinations BOX Joint BIT Combinations Service Troubleshooting MaintenanceAccessories Warranty PORTER-CABLE Limited ONE Year Warranty Canadian PORTER-CABLE Delta Service Centers Michigan