Manuals / Brands / Power Tools / Saw / Porter-Cable / Power Tools / Saw

Porter-Cable 4210, 4212 INLAYED HALF-BLIND DOVETAIL

1 44

Download 44 pages, 2.14 Mb

If desired, you can cut off the small area shown from the remainder of the inlay wood (Fig. 68C). If left on, the

completed joint will have an extra amount of material on the inside. another alternative is to bevel this extra material

(Fig. 68D).

MAKE THE SECOND JOINT

Make the second joint the same way as you would a standard through dovetail. HINT: Do not move the offset guides

after making the first joint.

Fig. 68C Fig. 68D

Fig. 69A Fig. 69B

INLAYED HALF-BLIND DOVETAIL

Make this joint by producing two half-blind dovetails on

top of each other.

Fig. 70B

CUT OFF THE INLAY BOARD

After the joint has dried, cut the inlay board to an amount equal to the thickness of the inlay (Fig. 68B).

Fig. 68A Fig. 68B

Contents

Main TABLE OF CONTENTS Back Cover SAFETY GUIDELINES - DEFINITIONS IMPORTANT SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. ADDITIONAL SAFETY RULES REPLACEMENT PARTS BACKGROUND INFORMATION OPERATION MISCELLANEOUS TECHNIQUES STOP NUT FOR BRASS ADJUSTMENT KNOB USE A DEAD-BLOW HAMMER CHAMFER THE TAIL EDGES THROUGH-DOVETAILS WITH CLAMPING BOARDS TEMPLATES MOUNTED TO CLAMPING BOARDS Page THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH Page ALTERNATE METHOD THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH HALF-BLIND DOVETAILS WITH CLAMPING BOARDS CUTTING THE JOINT USING A ROUTER TABLE HALF-BLIND DOVETAIL BITS THROUGH-DOVETAIL BIT COMBINATIONS (READILY AVAILABLE) ALTERNATE ROUTER BITS THROUGH-DOVETAIL BITS HALF-BLIND DOVETAIL BIT (READILY AVAILABLE) BIT COMBINATIONS FOR SEPARATE HALF-BLIND CUTS (READILY AVAILABLE) HALF-BLIND DOVETAIL BITS WITH THE TAILS AND PINS CUT SEPARATELY DOVETAIL DADO BITS BOX JOINT BITS BOX JOINT BITS (READILY AVAILABLE) HALF-BLIND DOVETAILS WITH TAIL BOARDS THICKER THAN 7/8" MITERING THE PINS MITERED THROUGH-DOVETAIL MITERING THE TAILS THROUGH-DOVETAIL, SKIPPED-PIN METHOD HALF-BLIND DOVETAIL, SKIPPED PIN METHOD Page SAW KERF ALLOWANCE METHOD Page END-TO-END JOINTS BOX END-TO-END JOINTS FITTING AND CUTTING THE JOINT MULTIPLE SPACER METHOD DOVETAIL END-TO-END JOINTS DRAWERS WITH DOVETAIL DADOS 180 HINGES WITH A DRILLED HOLE WOODEN HINGES 270 HINGES WITH A DRILLED HOLE 180 HINGES WITH ROUTER-MADE GROOVES 270 HINGES WITH ROUTER-MADE GROOVES ANGLED JOINTS OBTUSE ANGLED JOINTS SETUP WITH THE TEMPLATE MOUNTED TO THE BASE OF THE JIG CUTTING THE TAILS SETUP WITH THE TEMPLATE MOUNTED TO A CLAMPING BOARD CUTTING THE PINS ACUTE ANGLED JOINTS SLANTED-SIDE JOINTS COMPOUND-ANGLE JOINTS SETUP CUTTING THE PINS CUTTING THE TAILS INLAYED JOINTS INLAYED THROUGH DOVETAIL INLAYED HALF-BLIND DOVETAIL Page INLAYED BOX JOINT THROUGH DOVETAIL ROUTER BIT COMBINATIONS TABLES OF COMMONLY AVAILABLE ROUTER BIT SIZES HALF-BLIND DOVETAIL BITS COMBINATIONS FOR HALF-BLIND DOVETAILS WITH THE PINS AND THE TAILS CUT SEPARATELY. * BOX JOINT BIT COMBINATIONS REPLACEMENT PARTS SERVICE AND REPAIRS SERVICE ACCESSORIES TROUBLESHOOTING MAINTENANCE KEEP TOOL CLEAN WARRANTY PORTER-CABLE LIMITED ONE YEAR WARRANTY The following are trademarks of PORTER-CABLE DELTA (Las siguientes son marcas registradas de PORTER-CABLE DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE PORTER-CABLE DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE DELTA) Delta ms cercano. Delta deben obtenerse ponindose en contacto con cualquier distribuidor Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service Center, or Porter-Cable