Troubleshooting Maintenance, Service | Porter-Cable 4210, 4212

TROUBLESHOOTING

For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable help line at 1-800-487-8665.

MAINTENANCE

KEEP TOOL CLEAN

Periodically blow out all air passages with dry compressed air. Clean all plastic parts with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

WEAR ANSI Z87.1 SAFETY GLASSES WHILE USING COMPRESSED AIR.

SERVICE AND REPAIRS

All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE·DELTA FACTORY SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.).

SERVICE

REPLACEMENT PARTS

When servicing use only identical replacement parts.

SERVICE AND REPAIRS

All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE·DELTA FACTORY SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

A complete line of accessories is available from your Porter-Cable·Delta Supplier, Porter-Cable·Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier.

Since accessories other than those offered by Porter-Cable·Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Porter-Cable·Delta recommended accessories should be used with this product.

42

Image 42

Porter-Cable 4210, 4212 instruction manual Troubleshooting Maintenance, Service, Accessories

Contents

Supplementary Instructiondovetail JIG Manual Table of Contents Safety Guidelines Definitions Important Safety Instructions Additional Safety Rules Replacement PartsBackground Information Operation Miscellaneous Techniques Setup Templates Mounted to Clamping BoardsTHROUGH-DOVETAILS with Clamping Boards Cutting the Pins Cutting the Tails THROUGH-DOVETAILS with Unlimited Board Width Fitting the Joint Set the router bit depth, using the pencil mark from Step Fitting the joint is identical to the previous section a HALF-BLIND Dovetails with Clamping Boards Blind Dovetails with Tail Boards Thicker than 7/8 Cutting the Joint Wood Grain Using a Router Table Alternate Router Bits THROUGH-DOVETAIL BitsTHROUGH-DOVETAIL BIT Combinations Readily Available HALF-BLIND Dovetail BIT Readily Available BOX Joint Bits BOX Joint Bits Readily AvailableDovetail Dado Bits HALF-BLIND Dovetails with Tail Boards Thicker than 7/8 Mitering the Pins Mitered THROUGH-DOVETAIL THROUGH-DOVETAIL, SKIPPED-PIN Method Mitering the Tails HALF-BLIND DOVETAIL, Skipped PIN Method Cutting the Pins SAW Kerf Allowance Method Cutting the Tails Fitting and Cutting the Joint Multiple Spacer MethodEND-TO-END Joints BOX END-TO-END Joints Drawers with Dovetail Dados Dovetail END-TO-END Joints Wooden Hinges Hinges with a Drilled Hole Hinges with ROUTER-MADE Grooves Hinges with ROUTER-MADE Grooves Setup with the Template Mounted to the Base of the JIG Angled JointsObtuse Angled Joints Setup with the Template Mounted to a Clamping Board Cutting the Tails Cutting the Pins Acute Angled Joints SLANTED-SIDE Joints COMPOUND-ANGLE Joints Setup Blade Tilt Angle Make Angled CUT Inlayed Joints Inlayed Through DovetailMake the First Joint Inlayed HALF-BLIND Dovetail CUT OFF the Inlay BoardMake the Second Joint 100 13/128 050 042 028 014 Inlayed BOX Joint HALF-BLIND Dovetail Bits Tables of Commonly Available Router BIT SizesThrough Dovetail Router BIT Combinations BOX Joint BIT Combinations Troubleshooting Maintenance ServiceAccessories Warranty PORTER-CABLE Limited ONE Year Warranty Canadian PORTER-CABLE Delta Service Centers Michigan