Hinges with ROUTER-MADE Grooves | Porter-Cable 4210, 4212 specs

270° HINGES WITH ROUTER-MADE GROOVES

This method uses two pieces of wood glued together for each hinge-half. One of the pieces is very short.

Fig. 49A

Step 1 -

Step 2 -

Step 3 - Step 4 -

Step 5 - Step 6 -

Use a router to make a half-round dado near the end of a board. Make the diameter of the groove equal to the diameter of the hinge pin, and the depth of cut half the diameter of the hinge pin(Fig. 49B).

Round over the ends of the boards (Fig. 49C).

Cut off the ends of the boards. The length of the cut-off should be twice the thickness of the board (Fig. 49D).

Repeat Step 1 for the remaining longer boards.

For both hinge halves, glue the short board to the long board with the metal hinge rod in the grooves and sticking out both sides of the wood (Fig. 49E)

After the glue dries, remove the metal rod.

Make the rest of the hinge the same as you would with the 180° Hinge With a Drilled Hole.

Fig. 49B

Fig. 49C

Fig. 49D

Fig. 49E

28

Image 28

Porter-Cable 4210, 4212 instruction manual Hinges with ROUTER-MADE Grooves

Contents

Supplementary Instructiondovetail JIG Manual Table of Contents Safety Guidelines Definitions Important Safety Instructions Replacement Parts Additional Safety RulesBackground Information Operation Miscellaneous Techniques Templates Mounted to Clamping Boards SetupTHROUGH-DOVETAILS with Clamping Boards Cutting the Pins Cutting the Tails THROUGH-DOVETAILS with Unlimited Board Width Fitting the Joint Set the router bit depth, using the pencil mark from Step Fitting the joint is identical to the previous section a HALF-BLIND Dovetails with Clamping Boards Blind Dovetails with Tail Boards Thicker than 7/8 Cutting the Joint Wood Grain Using a Router Table THROUGH-DOVETAIL Bits Alternate Router BitsTHROUGH-DOVETAIL BIT Combinations Readily Available HALF-BLIND Dovetail BIT Readily Available BOX Joint Bits Readily Available BOX Joint BitsDovetail Dado Bits HALF-BLIND Dovetails with Tail Boards Thicker than 7/8 Mitering the Pins Mitered THROUGH-DOVETAIL THROUGH-DOVETAIL, SKIPPED-PIN Method Mitering the Tails HALF-BLIND DOVETAIL, Skipped PIN Method Cutting the Pins SAW Kerf Allowance Method Cutting the Tails Multiple Spacer Method END-TO-END JointsFitting and Cutting the Joint BOX END-TO-END Joints Drawers with Dovetail Dados Dovetail END-TO-END Joints Wooden Hinges Hinges with a Drilled Hole Hinges with ROUTER-MADE Grooves Hinges with ROUTER-MADE Grooves Angled Joints Setup with the Template Mounted to the Base of the JIGObtuse Angled Joints Setup with the Template Mounted to a Clamping Board Cutting the Tails Cutting the Pins Acute Angled Joints SLANTED-SIDE Joints COMPOUND-ANGLE Joints Setup Blade Tilt Angle Make Angled CUT Inlayed Through Dovetail Inlayed JointsMake the First Joint CUT OFF the Inlay Board Inlayed HALF-BLIND DovetailMake the Second Joint 100 13/128 050 042 028 014 Inlayed BOX Joint Tables of Commonly Available Router BIT Sizes Through Dovetail Router BIT CombinationsHALF-BLIND Dovetail Bits BOX Joint BIT Combinations Service Troubleshooting MaintenanceAccessories Warranty PORTER-CABLE Limited ONE Year Warranty Canadian PORTER-CABLE Delta Service Centers Michigan