Zeromatic, To search banks SR0-SR2 | Radio Shack 20-164 manual

To search banks SR0-SR2:

1.Press SRCH repeatedly to select SR0, SR1, or SR2.

2.To search the entire band, press FUNC then SRCH. “MAN” (Manual select) or “SRCH” (searches through the band) appears. The scanner starts searching while “SRCH” appears on the display. When the scanner finds an active frequency, it stops searching.

Press FUNC then SRCH again to return to the previous mode.

3.To select a channel while “MAN” appears on the display, press a channel number or use  or .

4.Adjust the Squelch.

5. If the scanner stops on an unwanted frequency, you can press L/OUT to lock out the frequency. For more information, see Locking Out Frequencies....

6.To pause while searching, press PSE. The scanner stops searching and *** PAUSED

***appears. To resume, press PSE again.

Zeromatic

While searching, the scanner stops if a transmission triggers the squelch setting. A narrow-band FM transmission can have a deviation of +/- 5 Khz, and the actual total bandwidth, including the tails of the sidebands, can be even greater. However, search intervals smaller than that can stop your scanner short of the correct (center) frequency.

The Zeromatic function allows the scanner to find the correct center frequency for search banks SR3, SR4, SR5, SR6 and SR7. When active, Zeromatic automatically tunes to the

f t

T

1

2

P

T

1

2

3

4

5

6

7

S

S r o

S f

20

Image 20

Radio Shack 20-164 manual Zeromatic, To search banks SR0-SR2

Contents

What’s Included Triple Trunking Contents Contents Volume / OFF Your Scanner To attach the supplied antenna Connecting the AntennaAttaching the Belt Clip Powering Your Scanner Batteries To install batteries To charge batteries External Power To use an external power source Headphones and Speakers Keytones and Keylock Backlight and ContrastTo set the keytone To lock the keypad To change the backlight mode Squelch and AttenuatorTo turn on the backlight To change the display contrast To set the attenuator mode To set squelch To turn the delay on / off Scanner SetupDelay Defining a Channel To define a channel Copying a Frequency To copy a frequency To delete all saved frequencies in a bank Deleting Saved FrequenciesTo delete a saved frequency To save a Ctcss or DCS code Scanner CloningTo define a channel’s Ctcss or DCS code Searching Seek SearchTo clone the scanner data To activate Seek Search Search Banks To search preprogrammed search banks Zeromatic To search banks SR0-SR2 Signal Stalker Programming a Search RangeTo activate Zeromatic To program the search range of Bank SR7 Special Signal Stalker To use Signal Stalker To use Special Signal Stalker Locking Out FrequenciesTo lock out a frequency To review and unlock frequencies To save a frequency found during a search Saving Found FrequenciesTo unlock all frequencies in a search bank Scanning Locking Out ChannelsTo scan To locked out a channel To review all locked out channels To turn on the priority featurePriority Scanning To modify the Priority channel Weather AlertsTo make an existing channel a Priority channel Same Standby Mode To perform a weather scanTo program a weather channel into priority channel To program a Fips code Code. The format of a Fips code is To review stored Fips codes To test the weather alert SkywarnTo enter Same standby Monitoring To use SkywarnTo monitor a channel To find a frequency to monitor Trunking Setup To set a default tuning frequencyDefining a Trunking Bank To define a Trunking Bank Trunking Modes Motorola Trunking SetupTo set Open or Closed mode for a bank Fleet Maps To program a fleet map Base and Offset Frequencies For Motorola Type II, enter Edacs Trunking Setup UHF-Hi 806-960 MHz To program 800 MHz Motorola trunking LTR Trunking Setup To save a correct Home Repeater To search for Talk Group IDs Searching for Talk Group IDsSaving a Talk Group ID Deleting Talk Group IDs To define a Talk Group ID To delete ALL talk group IDs in a bank Saving Trunking ChannelsTo delete a Talk Group ID Trunk Scanning To change the scanning direction, press  or  Trunking Delay To set a Talk Group ID delayLocking Out Talk Group IDs To lock out Talk Group IDs Turning Off Sub-Banks To review locked-out Talk Group IDsTo turn off a sub-bank To turn off a sub-bank while scanning Scanner Maintenance Talk Group ID HoldText Tags To set Talk Group ID HoldPage Troubleshooting To display the Talk Group IDScanner is not Working at all Scanner does not Receive any stations Or reception is poorScanner is on but Does not scan Birdie Frequencies To initialize the scanner Service and RepairInitializing the Scanner Scanning Legally FCC Notice Appendix B Search Banks ReferencesAppendix a Glossary Search bank SR1 CB band Receive mode AM Search bank SR2 FRS/GMRS/MURS band Search bank SR4 Aircraft Receive mode AM, FM Appendix C Ctcss / DCS Codes Ctcss Codes DCS Codes Appendix D Signal Stalker BandsAll Band PubSafety Band To use AFS format Appendix E Talk Group FormatMotorola Appendix F Specifications 406-512 MHz 764-960 MHz 9V DC Addendum Preprogrammed Frequencies Purple DOT Purple DOT BB Business Band Police Departments Police Dept Nascar Track Announcer Security Alarm Security Company Companies DOT Business Band DOT BB Limited One-year Warranty