Manuals / Radio Shack / Computer Equipment / Scanner

Radio Shack 20-164 manual Code. The format of a Fips code is, To review stored Fips codes

Models: 20-164

1 68

Download 68 pages 17.08 Kb

Page 29

4.		Use the number keys to enter the FIPS
		code. The format of a FIPS code is:

		Subdivisions	State Code	County Code

		0-9	01-50	XXX
		(0=entire area)	(00=all states)	(000=all counties)

			Example: 048439
		(0=All; 48=Texas; 439=Tarrant County)

5.		(Optional) To label the code, press TEXT
		and use the letter buttons to enter text.
6.		Press ENT to store the code. Repeat this
		process to program additional FIPS codes.

7. Press L/OUT to lock out or enable specific FIPS entries.

8. Press WX to exit the FIPS code entry table.

To review stored FIPS codes:

1.Press WX then a number key.

2.Press L/OUT to change the lockout status.

	a	The scanner sounds an alert or beep
	a	when it receives the SAME code. If
		when it receives the SAME code. If
		you do not stop the alert (or beep) for
		five minutes, the alert stops and the
		scanner beeps every ten seconds. If the
		scanner receives a new message after
		five minutes, it sounds the alert or beep.
		Press any key except LIGHT to stop the
		alert and allow the scanner to receive a
		new alert signal before the five minute
		time out.
		For information about adding text tags to
		a FIPS code, see “Text Tags” on Page 44.

29

Image 29

Radio Shack 20-164 manual Code. The format of a Fips code is, To review stored Fips codes

Contents

Triple Trunking What’s IncludedContents Contents Your Scanner Volume / OFFTo attach the supplied antenna Connecting the AntennaAttaching the Belt Clip Batteries Powering Your ScannerTo charge batteries To install batteriesTo use an external power source External PowerHeadphones and Speakers Backlight and Contrast Keytones and KeylockTo set the keytone To lock the keypadSquelch and Attenuator To change the backlight modeTo turn on the backlight To change the display contrastTo set squelch To set the attenuator modeTo turn the delay on / off Scanner SetupDelay To define a channel Defining a ChannelTo copy a frequency Copying a FrequencyTo delete all saved frequencies in a bank Deleting Saved FrequenciesTo delete a saved frequency To save a Ctcss or DCS code Scanner CloningTo define a channel’s Ctcss or DCS code Seek Search SearchingTo clone the scanner data To activate Seek SearchTo search preprogrammed search banks Search BanksTo search banks SR0-SR2 ZeromaticProgramming a Search Range Signal StalkerTo activate Zeromatic To program the search range of Bank SR7To use Signal Stalker Special Signal StalkerLocking Out Frequencies To use Special Signal StalkerTo lock out a frequency To review and unlock frequenciesTo save a frequency found during a search Saving Found FrequenciesTo unlock all frequencies in a search bank Locking Out Channels ScanningTo scan To locked out a channelTo review all locked out channels To turn on the priority featurePriority Scanning To modify the Priority channel Weather AlertsTo make an existing channel a Priority channel To perform a weather scan Same Standby ModeTo program a weather channel into priority channel To program a Fips codeTo review stored Fips codes Code. The format of a Fips code isTo test the weather alert SkywarnTo enter Same standby To use Skywarn MonitoringTo monitor a channel To find a frequency to monitorTo set a default tuning frequency Trunking SetupDefining a Trunking Bank To define a Trunking BankTrunking Modes Motorola Trunking SetupTo set Open or Closed mode for a bank To program a fleet map Fleet MapsFor Motorola Type II, enter Base and Offset FrequenciesUHF-Hi 806-960 MHz To program 800 MHz Motorola trunking Edacs Trunking SetupTo save a correct Home Repeater LTR Trunking SetupTo search for Talk Group IDs Searching for Talk Group IDsSaving a Talk Group ID To define a Talk Group ID Deleting Talk Group IDsTo delete ALL talk group IDs in a bank Saving Trunking ChannelsTo delete a Talk Group ID To change the scanning direction, press  or  Trunk ScanningTo set a Talk Group ID delay Trunking DelayLocking Out Talk Group IDs To lock out Talk Group IDsTo review locked-out Talk Group IDs Turning Off Sub-BanksTo turn off a sub-bank To turn off a sub-bank while scanningTalk Group ID Hold Scanner MaintenanceText Tags To set Talk Group ID HoldPage To display the Talk Group ID TroubleshootingScanner is not Working at allReceive any stations Or reception is poor Scanner does notScanner is on but Does not scanBirdie Frequencies To initialize the scanner Service and RepairInitializing the Scanner Scanning Legally FCC Notice Appendix B Search Banks ReferencesAppendix a Glossary Search bank SR1 CB band Receive mode AM Search bank SR2 FRS/GMRS/MURS band Search bank SR4 Aircraft Receive mode AM, FM Ctcss Codes Appendix C Ctcss / DCS CodesDCS Codes Appendix D Signal Stalker BandsAll Band PubSafety Band To use AFS format Appendix E Talk Group FormatMotorola 406-512 MHz 764-960 MHz Appendix F Specifications9V DC Preprogrammed Frequencies AddendumPurple DOT Purple DOT BB Business Band Police Departments Police Dept Nascar Track Announcer Security Alarm Security Company Companies DOT Business Band DOT BB Limited One-year Warranty