Raypak 133-4001 manual For Your Safety Read Before Operating, For Models with Manual Gas Valves

LIGHTING INSTRUCTIONS FOR BOILERS WITH ELECTRONIC IGNITION (IID)

For Models with Manual Gas Valves

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A. This appliance is equipped with an ignition device which * automatically lights the pilot. Do not try to light the pilot by hand.

If you cannot reach your gas supplier, call the fire de- partment.

B.	BEFORE OPERATING smell all around the appliance	C. Use only your hand to push in or turn the gas control
		knob. Never use tools. If the knob will not push in or turn
	area for gas. Be sure to smell next to the floor because	by hand, do not try to repair it, call a qualified service
	some gas is heavier than air and will settle on the floor.	technician. Force or attempted repair may result in a fire
	WHAT TO DO IF YOU SMELL GAS	or explosion.
*	Do not try to light any appliance.
*	Do not touch any electric switch; do not use any phone	D. Do not use this appliance if any part has been under
	in your building.	water. Immediately call a qualified service technician to
*	Immediately call your gas supplier from your neighbor’s	inspect the appliance and to replace any part of the
	phone. Follow the gas supplier’s instructions.	control system and any gas control which has been
		under water.

OPERATING INSTRUCTIONS

1.STOP! Read the safety information above.

2.Set the thermostat on the lowest setting.

3.Turn off all electrical power to the appliance.

4.This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

5.Remove boiler door panel.

6.For Robertshaw gas valve: Turn gas control knob

clockwise to “OFF”.

For Honeywell gas valve (all models except 40#):

Turn gas control knob clockwise to “OFF".

Make sure knob rest against stop.

For Honeywell gas valve (Models 40# only): Push in gas control knob slightly and turn clockwise

to “OFF”. Knob cannot be turned to “OFF” unless knob is pushed in slightly. Do not force.

7.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If

you do not smell gas, go to the next step.

8.For Robertshaw gas valve: Turn gas control knob

counter-clockwise to “ON”.

ROBERTSHAW

GAS CONTROL

KNOB SHOWN

IN "ON" POSITION

GAS INLET

For Honeywell gas valve: Turn gas control knob

counter-clockwise from “OFF” until it stops. Push in gas control knob and continue

rotating counter-clockwise to “ON” position. Make sure knob rests against stop.

HONEYWELL

GAS CONTROL

KNOB SHOWN

IN "ON" POSITION

GAS INLET

For Honeywell gas valve (Models 40# only):

Turn gas control knob counter-clockwise to “ON”.

GAS CONTROL KNOB

SHOWN IN "ON"

POSITION

GAS INLET

9.Replace boiler door panel.

10.Turn on all electrical power to the appliance.

11.Set thermostat to desired setting.

12.If the appliance will not operate, follow the instructions “To Turn Off Gas To Appliance” and call your service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1.	Set the thermostat to the lowest setting.		Turn gas control knob clockwise	to “OFF”.
2.	Turn off all the electrical power to the appliance if service		Make sure knob rests against stop.
	is to be performed.		For Honeywell gas valve (Models 40# only):
3.	Remove door panel.		Push in gas control knob slightly and turn clockwise
4.	For Robertshaw gas valve: Turn gas control knob		to “OFF”.
	clockwise	to “OFF”.	5. Replace heater door panel.

For Honeywell gas valve (all models except 40#):

27