Manuals / Regency / Household Appliance / Indoor Fireplace

Regency P33-NG4 installation manual thoroughly before it leaves our door

Models: P33-NG4

1 52

Download 52 pages 58.5 Kb

Page 52

thoroughly before it leaves our

Regency® ﬁreplace products are designed with reliability and simplicity in mind. In addition, our internal QualityAssurance Team carefully inspects each unit

thoroughly before it leaves our

door.

Manual background Fireplace Products International Ltd. is pleased to extend this Limited Lifetime Warranty to the

original purchaser of a Regency® Product.

See the inside back cover for details.

Register your Regency® online at

http://www.regency-ﬁre.com

Installer: Please complete the following information

Dealer Name & Address:______________________________________________

___________________________________________________________________

Installer: ___________________________________________________________

Phone #: ___________________________________________________________

Date Installed: ______________________________________________________

Serial No.:__________________________________________________________

Regency® and Panorama are trademarks of FPI Fireplace Products International Ltd.

© Copyright 2006, FPI Fireplace Products International Ltd. All rights reserved.

Printed in Canada

52	Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

Image 52

Regency P33-NG4 installation manual thoroughly before it leaves our door

Contents

Installation Manual P33-4Zero ClearanceDirect Vent Gas Fireplace OwnersTo the New Owner INSTALLATION MAINTENANCEPARTS LIST WARRANTYSAFETY LABEL SAFETY LABELREQUIREMENTS MA Code - CO Detector5.08 Modifications to NFPA-54,Chapter OBSTRUCTIONSINSTALLATION GENERAL SAFETY INFORMATIONIMPORTANT MESSAGE BEFORE YOU STARTINSTALLATION CHECKLIST UNIT DIMENSIONSVent Termination Locations Section Diagram LOCATING YOUR FIREPLACECLEARANCES MANTEL LEG CLEARANCESCOMBUSTIBLE MANTELS Clearance to Combustibles fromFRAMING AND FINISHING Rigid VentMinimum Clearances Flex VentUNIT ASSEMBLY PRIOR TO INSTALLATION Top Standoff AssemblyVENTING INTRODUCTION Top Facing Support & Side Nailing StripsEXTERIOR VENT TERMINATION LOCATIONS REGENCY DIRECT VENT FLEX SYSTEM MINIMUM RIGID PIPE CENTER-LINEMINIMUM FLEX KIT CENTER-LINE CapsINSTALLATION PROCEDURES RIGID PIPE VENTING SYSTEMS AlternateCaps HorizontalRIGID PIPE VENTING COMPONENTS LIST DescriptionSimpson Dura-Vent SelkirkRIGID PIPE VENTING ARRANGEMENTS Vertical Terminations Propane & Natural GasVent must be supported at offsets Maintain clearances to combustiblesVent must be supported at offsets The P33-4is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural GasMaintain clearances to combustibles RIGID PIPE VENTING ARRANGEMENTS REGENCY DIRECT VENT SYSTEM FLEXSimpson Dura-Vent Center-Line Flex Kit Center-LineINSTALLATION Horizontal Venting with Two 2 90o ElbowsHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsVertical Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsVertical Venting with Two 2 90o Elbows Vertical Venting with Three 3 90o Elbows Vertical Venting with Three 3 90o ElbowsOption H + H1VERTICAL TERMINATION WITH CO-LINEARFLEX SYSTEM Co-linearDV Vertical Termination Cap #Amaximum of two certified joiner kits may be used per length. #948-30535 ft 11mThe shaded area in the diagrams show VENTING ARRANGEMENTS - VERTICAL TERMINATIONSVerticalHeightfeet Horizontal Distance FeetUNIT INSTALLATION WITH HORIZONTAL TERMINATION DiagramDiagram DiagramUNIT INSTALLATION WITH VERTICAL TERMINATION GAS LINE INSTALLATIONDiagram DiagramPILOT ADJUSTMENT GAS PIPE PRESSURE TESTINGHIGH ELEVATION S.I.T. VALVE DESCRIPTIONFor P33-4/H25-1Using SIT 820 NOVA Gas Valve Installation of the LPG Conversion KitAssembly to the left and lift out Pilot assembly is now accessible for steps 4 toDo not overtighten the screw. Recommended to grip the wrench by the short sideAlso check that the pilot and main burner injectorsIgnitor Wire Piezo Ignitor DC Sparker Ignitor WireGround wire from kit Battery CompartmentLOG SET INSTALLATION OPTIONAL BRICKPANELS Note The logs must not be in the unitDiagram DiagramDiagram STANDARD FLUSH DOORDiagram Clip locations Clip installed on right sideFLUSH LOUVERS DOUBLE SCREEN DOORBAY LOUVERS Flush Louver Top Heat ShieldBay Louver Top Heat Shield Burner ON/OFF control boxFULL SCREEN DOORS Backside of FullFlange Screen Door Frame ShownCut-Out Oblong Hole Cut-Out Top Flange Bottom Cut-OutsHinge Location Bottom Grill HingeLeft Side of Bottom Grill Screen Door Top GrillOptional REMOTE CONTROL Optional WALL SWITCHDo not wire millivolt wall switch wire to 120V wireWIRING DIAGRAMS ThermopileThermocouple GasPilotPage INSTALLING THE OPTIONAL FAN 1 Shut the power offDiagram Diagram 3 Use the clip & hook on the side ofCOPY OF THE LIGHTING PLATE INSTRUCTIONS OPERATING INSTRUCTIONSGas Inlet LIGHTING PROCEDURE SHUTDOWN PROCEDUREAERATION ADJUSTMENT CLEAN THE GLASS WHILE IT IS HOTMAINTENANCE LOG REPLACEMENTMAINTENANCE NORMAL OPERATING SOUNDS OFFlush Glass Replacement Bay Glass ReplacementTHERMOPILE THERMOCOUPLE GLASS GASKETINSTALLING VALVE Diagram 3 Lift out Valve Tray AssemblyValve Tray Assembly Diagram 2 Rear Log Stand & Valve Tray AssemblyPARTS LIST MAIN ASSEMBLYPARTS LIST BURNER & LOG ASSEMBLY Part DescriptionFLUSH FRONT & LOUVERS BAY FRONT & LOUVERS Page WARRANTY The Warranty Limited LifetimeConditions Exclusionsthoroughly before it leaves our door