Manuals / Regency / Household Appliance / Indoor Fireplace

Regency P33-NG4 Vent must be supported at offsets, Maintain clearances to combustibles

Models: P33-NG4

1 52

Download 52 pages 58.5 Kb

Page 17

Image 17

INSTALLATION

The P33-4 is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural Gas.

The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations with rigid pipe vent systems for Propane and Natural Gas. Maximum two 45o elbows allowed.

•Vent must be supported at offsets.

•Firestops are required at each ﬂoor level and whenever passing through a wall.

•Maintain clearances to combustibles.

Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

Page 17

Image 17

Regency P33-NG4 installation manual Vent must be supported at offsets, Maintain clearances to combustibles

Contents

P33-4Zero Clearance Installation ManualDirect Vent Gas Fireplace OwnersTo the New Owner MAINTENANCE INSTALLATIONPARTS LIST WARRANTYSAFETY LABEL SAFETY LABELMA Code - CO Detector REQUIREMENTS5.08 Modifications to NFPA-54,Chapter OBSTRUCTIONSGENERAL SAFETY INFORMATION INSTALLATIONIMPORTANT MESSAGE BEFORE YOU STARTUNIT DIMENSIONS INSTALLATION CHECKLISTVent Termination Locations Section Diagram LOCATING YOUR FIREPLACEMANTEL LEG CLEARANCES CLEARANCESCOMBUSTIBLE MANTELS Clearance to Combustibles fromRigid Vent FRAMING AND FINISHINGMinimum Clearances Flex VentTop Standoff Assembly UNIT ASSEMBLY PRIOR TO INSTALLATIONVENTING INTRODUCTION Top Facing Support & Side Nailing StripsEXTERIOR VENT TERMINATION LOCATIONS MINIMUM RIGID PIPE CENTER-LINE REGENCY DIRECT VENT FLEX SYSTEMMINIMUM FLEX KIT CENTER-LINE CapsINSTALLATION PROCEDURES Alternate RIGID PIPE VENTING SYSTEMSCaps HorizontalDescription RIGID PIPE VENTING COMPONENTS LISTSimpson Dura-Vent SelkirkVertical Terminations Propane & Natural Gas RIGID PIPE VENTING ARRANGEMENTSVent must be supported at offsets Maintain clearances to combustiblesMaintain clearances to combustibles The P33-4is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural GasVent must be supported at offsets REGENCY DIRECT VENT SYSTEM FLEX RIGID PIPE VENTING ARRANGEMENTSSimpson Dura-Vent Center-Line Flex Kit Center-LineHorizontal Venting with Two 2 90o Elbows INSTALLATIONHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsVertical Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsVertical Venting with Two 2 90o Elbows Vertical Venting with Three 3 90o Elbows Vertical Venting with Three 3 90o ElbowsOption H + H1Co-linearDV Vertical Termination Cap # VERTICAL TERMINATION WITH CO-LINEARFLEX SYSTEMAmaximum of two certified joiner kits may be used per length. #948-30535 ft 11mVENTING ARRANGEMENTS - VERTICAL TERMINATIONS The shaded area in the diagrams showVerticalHeightfeet Horizontal Distance FeetDiagram UNIT INSTALLATION WITH HORIZONTAL TERMINATIONDiagram DiagramGAS LINE INSTALLATION UNIT INSTALLATION WITH VERTICAL TERMINATIONDiagram DiagramGAS PIPE PRESSURE TESTING PILOT ADJUSTMENTHIGH ELEVATION S.I.T. VALVE DESCRIPTIONInstallation of the LPG Conversion Kit For P33-4/H25-1Using SIT 820 NOVA Gas ValveAssembly to the left and lift out Pilot assembly is now accessible for steps 4 tothe wrench by the short side Do not overtighten the screw. Recommended to gripAlso check that the pilot and main burner injectorsDC Sparker Ignitor Wire Ignitor Wire Piezo IgnitorGround wire from kit Battery CompartmentOPTIONAL BRICK LOG SET INSTALLATIONPANELS Note The logs must not be in the unitDiagram DiagramDiagram STANDARD FLUSH DOORClip locations Clip installed on right side DiagramFLUSH LOUVERS DOUBLE SCREEN DOORFlush Louver Top Heat Shield BAY LOUVERSBay Louver Top Heat Shield Burner ON/OFF control boxBackside of FullFlange Screen Door Frame Shown FULL SCREEN DOORSCut-Out Oblong Hole Cut-Out Top Flange Bottom Cut-OutsHinge Hinge Location Bottom GrillLeft Side of Bottom Grill Screen Door Top GrillOptional WALL SWITCH Optional REMOTE CONTROLDo not wire millivolt wall switch wire to 120V wireThermopile WIRING DIAGRAMSThermocouple GasPilotPage 1 Shut the power off INSTALLING THE OPTIONAL FANDiagram Diagram 3 Use the clip & hook on the side ofGas Inlet OPERATING INSTRUCTIONSCOPY OF THE LIGHTING PLATE INSTRUCTIONS SHUTDOWN PROCEDURE LIGHTING PROCEDUREAERATION ADJUSTMENT CLEAN THE GLASS WHILE IT IS HOTLOG REPLACEMENT MAINTENANCEMAINTENANCE NORMAL OPERATING SOUNDS OFBay Glass Replacement Flush Glass ReplacementTHERMOPILE THERMOCOUPLE GLASS GASKETDiagram 3 Lift out Valve Tray Assembly INSTALLING VALVEValve Tray Assembly Diagram 2 Rear Log Stand & Valve Tray AssemblyMAIN ASSEMBLY PARTS LISTPARTS LIST Part Description BURNER & LOG ASSEMBLYFLUSH FRONT & LOUVERS BAY FRONT & LOUVERS Page The Warranty Limited Lifetime WARRANTYConditions Exclusionsthoroughly before it leaves our door