Manuals / Regency / Household Appliance / Indoor Fireplace

Regency P33-NG4 Venting Arrangements - Vertical Terminations, VerticalHeightfeet, 762mm

Models: P33-NG4

1 52

Download 52 pages 58.5 Kb

Page 23

Image 23

INSTALLATION

VENTING ARRANGEMENTS - VERTICAL TERMINATIONS

with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces

	30
VerticalHeight(feet)	(51mm)max.	8'(2.4m)Min.	30'(9.1m)Max.
	2’
		30”	(762mm)

Horizontal Distance (Feet)

The shaded area in the diagrams show

the allowable vertical terminations.

Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

Page 23

Image 23

Regency P33-NG4 Venting Arrangements - Vertical Terminations, VerticalHeightfeet, Horizontal Distance Feet, 762mm

Contents

Owners Installation ManualP33-4Zero Clearance Direct Vent Gas FireplaceTo the New Owner WARRANTY INSTALLATIONMAINTENANCE PARTS LISTSAFETY LABEL SAFETY LABELOBSTRUCTIONS REQUIREMENTSMA Code - CO Detector 5.08 Modifications to NFPA-54,ChapterBEFORE YOU START INSTALLATIONGENERAL SAFETY INFORMATION IMPORTANT MESSAGELOCATING YOUR FIREPLACE INSTALLATION CHECKLISTUNIT DIMENSIONS Vent Termination Locations Section DiagramClearance to Combustibles from CLEARANCESMANTEL LEG CLEARANCES COMBUSTIBLE MANTELSFlex Vent FRAMING AND FINISHINGRigid Vent Minimum ClearancesTop Facing Support & Side Nailing Strips UNIT ASSEMBLY PRIOR TO INSTALLATIONTop Standoff Assembly VENTING INTRODUCTIONEXTERIOR VENT TERMINATION LOCATIONS Caps REGENCY DIRECT VENT FLEX SYSTEMMINIMUM RIGID PIPE CENTER-LINE MINIMUM FLEX KIT CENTER-LINEINSTALLATION PROCEDURES Horizontal RIGID PIPE VENTING SYSTEMSAlternate CapsSelkirk RIGID PIPE VENTING COMPONENTS LISTDescription Simpson Dura-VentMaintain clearances to combustibles RIGID PIPE VENTING ARRANGEMENTSVertical Terminations Propane & Natural Gas Vent must be supported at offsetsMaintain clearances to combustibles The P33-4is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural GasVent must be supported at offsets Flex Kit Center-Line RIGID PIPE VENTING ARRANGEMENTSREGENCY DIRECT VENT SYSTEM FLEX Simpson Dura-Vent Center-LineHorizontal Venting with Two 2 90o Elbows INSTALLATIONHorizontal Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsVertical Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsVertical Venting with Two 2 90o Elbows H + H1 Vertical Venting with Three 3 90o ElbowsVertical Venting with Three 3 90o Elbows Optionmay be used per length. #948-30535 ft 11m VERTICAL TERMINATION WITH CO-LINEARFLEX SYSTEMCo-linearDV Vertical Termination Cap # Amaximum of two certified joiner kitsHorizontal Distance Feet The shaded area in the diagrams showVENTING ARRANGEMENTS - VERTICAL TERMINATIONS VerticalHeightfeetDiagram UNIT INSTALLATION WITH HORIZONTAL TERMINATIONDiagram DiagramDiagram UNIT INSTALLATION WITH VERTICAL TERMINATIONGAS LINE INSTALLATION DiagramS.I.T. VALVE DESCRIPTION PILOT ADJUSTMENTGAS PIPE PRESSURE TESTING HIGH ELEVATIONPilot assembly is now accessible for steps 4 to For P33-4/H25-1Using SIT 820 NOVA Gas ValveInstallation of the LPG Conversion Kit Assembly to the left and lift outmain burner injectors Do not overtighten the screw. Recommended to gripthe wrench by the short side Also check that the pilot andBattery Compartment Ignitor Wire Piezo IgnitorDC Sparker Ignitor Wire Ground wire from kitNote The logs must not be in the unit LOG SET INSTALLATIONOPTIONAL BRICK PANELSSTANDARD FLUSH DOOR DiagramDiagram DiagramDOUBLE SCREEN DOOR DiagramClip locations Clip installed on right side FLUSH LOUVERSBurner ON/OFF control box BAY LOUVERSFlush Louver Top Heat Shield Bay Louver Top Heat ShieldCut-Outs FULL SCREEN DOORSBackside of FullFlange Screen Door Frame Shown Cut-Out Oblong Hole Cut-Out Top Flange BottomTop Grill Hinge Location Bottom GrillHinge Left Side of Bottom Grill Screen Doorto 120V wire Optional REMOTE CONTROLOptional WALL SWITCH Do not wire millivolt wall switch wireGasPilot WIRING DIAGRAMSThermopile ThermocouplePage Diagram 3 Use the clip & hook on the side of INSTALLING THE OPTIONAL FAN1 Shut the power off DiagramGas Inlet OPERATING INSTRUCTIONSCOPY OF THE LIGHTING PLATE INSTRUCTIONS CLEAN THE GLASS WHILE IT IS HOT LIGHTING PROCEDURESHUTDOWN PROCEDURE AERATION ADJUSTMENTNORMAL OPERATING SOUNDS OF MAINTENANCELOG REPLACEMENT MAINTENANCEGLASS GASKET Flush Glass ReplacementBay Glass Replacement THERMOPILE THERMOCOUPLEDiagram 2 Rear Log Stand & Valve Tray Assembly INSTALLING VALVEDiagram 3 Lift out Valve Tray Assembly Valve Tray AssemblyMAIN ASSEMBLY PARTS LISTPARTS LIST Part Description BURNER & LOG ASSEMBLYFLUSH FRONT & LOUVERS BAY FRONT & LOUVERS Page Exclusions WARRANTYThe Warranty Limited Lifetime Conditionsthoroughly before it leaves our door

VENTING ARRANGEMENTS - VERTICAL TERMINATIONS

VerticalHeight(feet)

(762mm)

Horizontal Distance (Feet)

The shaded area in the diagrams show

the allowable vertical terminations.