Adding Toner, 121 | Ricoh 340 specification

D ADDING TONER

D ADDING TONER

When D is displayed, it is time to supply toner.

RWARNING:

•Do not incinerate used toner or toner containers. Toner dust

might ignite when exposed to an open flame. Dispose of the used toner containers according to local regulations for plastics.

RCAUTION:

•Do not eat or swallow toner.

• Keep toner (used or unused) and toner containers out of reach of children.

RCAUTION:

•This machine has been tested for safety using this supplier's

parts and consumables. We recommend you only use these specified supplies.

Important

❒If you use toner other than that recommended, a fault might occur.

❒When adding toner, do not turn off the operation switch. If you do, your set- tings are cleared.

❒Always add toner after the machine instructs you to add toner.

❒Do not use used toner. This will damage the machine.

Note

❒You can still make about 50 copies after the D appears, but replace the toner early to prevent poor copy quality.

Reference

Regarding toner storage, see Þ P.27 “Toner Storage”.

• 1: Open the front cover of the machine.

• 2: Lift the green holder.

3

Toner1

121

Image 137

Ricoh 340 manual Adding Toner, 121

Contents

340/350/450 Following label is attached on the back side of the machine Examples Of Indications Safety InformationSafety During Operation Page Iii Page Page Symbols HOW to Read this Manual Vii Viii What YOU can do with this Machine Copy Mode RR Rrrr Table of Contents Preset REDUCE/ENLARGE-REDUCING and Enlarging Using 108 102111 113 150 148165 166 Xiv Machine Types Guide to Components Duplex unit Unit for two-sided copiesoption for Type Operation panelFront cover Paper tray Ventilation hole Bypass tray option for TypeRight side cover Lower right cover To copy onto A3, 11 × 17 paper Guide If the end of the sheet is curled Type Options Sheet finisher only for Type Type 2 and Type Function List Based on Options Page Page Panel display IndicatorsOperation Panel Keys Cursor keys Shortcut keys Displays And Key Operations Panel DisplayCopy initial display Displays items which can be selected or specified Common keys Function menu display Sample Display for Erasing the Centre/Border Display Panel Layout Power switches Turning On The PowerOperation switch right side of the op- eration panel Main power switch left side of the ma- chine When the Clear Modes/Energy Saver indicator is lit Turning Off The PowerPress the operation switch to make the On indicator go off Er key Changing Modes Originals Sizes And Weights Of Recommended OriginalsMetric version Inch version Sizes detectable by the Auto Paper Select Metric version Sizes Difficult To Detect Document feeder Original Sizes And Scanning Area/Missing Image AreaExposure glass Recommended Paper Sizes And Types Copy Paper Reference Non-recommended Paper Paper Storage Used Toner TonerToner Storage Basics Make sure that the machine is Copy mode Basic ProcedureMake sure that there are no previ- ous settings remaining Set your originals Auto Off Auto Reset Setting Originals On Exposure Glass Setting OriginalsLift the platen cover or the docu Ment feeder Lower the platen cover or the doc- ument feeder Setting a stack of originals in the document feeder Setting Originals Document FeederWhen Sadf mode is selected Set the next original while Auto Feed indicator is lit Sadf mode Using SADF, Mixed Sized, and Thin Paper modesPress the Menu key Press the ↓Next key until DF Set- ting is displayed Select DF Setting with the keys, then press the Select key Mixed sizes modePress the Select key Press the Exit key Thin paper mode Select Thin Paper with the keys, then press the Select key Basic Functions Adjusting Copy Image Density Enhanced Image Copy Key to cancel itManual Image Density Combined Auto and Manual Image Density Selecting Original Type Setting Special Original Selecting Copy PaperAuto Paper Select Manual Paper Select Manual Paper Select Auto Paper SelectSelect the copy paper Make sure that the Auto Auto Paper Select is selected Select the paper tray by pressing the Paper or Machine Choose Reproduction Ratios Sort SORT/STACK/STAPLEStack Staple the optional 1000-sheet finish- er required 144 y Removing Punch Waste Sort Rotate Sort Shift Sort Sort-Sorting Into Sets 123, 123 When setting a stack of originals in the document feeder Rotate Stack Shift Stack Stack-Stacking Together All Copies Of a Page 111, 222Rotate Stack Shift Stack optional finisher re- quired Then, press the OK key Press the Sorter key until Stack indicator bottom is litMake sure that on is selected Staple A4KL B5K B5KL Sheet finisher Stapling position and original setting Press the OK key Select one of four stapling posi- tions To stop scanning When memory reaches 0 %To resume scanning To clear scanned images of the originals Press the Start key Copying from the Bypass Tray Adjust the guides to copy paper size When copying onto non-standard size copy paper Make sure the k indicator is selected When copying onto standard size copy paperPress the # key Press the Ppr.Size key Press the ↓Next key until your desired size is displayed Press the # key Press the Ppr.Type key When copying onto OHP transparencies or thick paper Set your originals and press the Start key Storing Your Settings PROGRAM-STORING Your Copy Settings in MemoryStoring Your Settings Deleting a Program Deleting a Program Recalling a Program User Codes Other FunctionsEnergy Saver Mode-Saving Energy Original Beeper Auto Start-Entering Copy Job Settings During Warm-up Period Original → Copy paper Ratio % Size Press the Enlarge or Reduce key to select a ratio ZOOM-REDUCING and Enlarging in 1 % Steps When using the n or o keyWhen using the Number keys Set your originals, then press the Start key Metric version Mm steps Inch version 99.9 Steps Copying Horizontal % Select the Direct. Mag. % key with or key. Then, press ND2C0104 Enter the desired margin width with the Number keys Margin ADJUSTMENT-ADJUSTING the MarginSelect Left left margin or Right right margin with the keys ND2C0101 Erase Centre Erase CENTRE/BORDER-ERASING the Centre and the BorderErase Border Centre Border CentreSelect the part to be erased Press the Centre key Set your originals, then press the Start key Pages→1-sided COMBINE-COMBINING Originals Into ONE CopyPages→booklet Duplex unit COMBINE-COMBINING Originals Into ONE Copy Press the ↓Next key until the Combine is displayed Making a booklet Book → 1-Sided With the optional document feeder Without the optional documentFeeder Press the ↓Next key until Series is displayed Sided OriginalsSelect Series with the keys Book → 2-sided DUPLEX-MAKING TWO-SIDED CopiesSided → 2-sided Top to Bottom Originals and copy direction Top Specifying Orientation of Bound Originals Original Copy paper When setting a stack of originals in the document feeder Adding a Front Cover COVER/PAPER DESIGNATE-ADDING or Inserting Sheets Press the Menu key Press the Both key Both Covers-Copying Or Adding Front And BackPress the ↓Next key until Cover Ppr. Des. is displayed Press the Exit key Press the Ppr.Des. key Press the ↓Next key until OHP Slip Sheet is displayed OHP Slip SHEET-COPYING or Inserting Slip Sheet OHP Slip SHEET-COPYING or Inserting Slip Sheet POSITIVE/NEGATIVE-COPYING in Complementaly Colors Double Copies Image REPEAT-REPEATING AN ImageImage Repeat Double Copies-Copying The Image Twice On One Original A5K/Copy paper A4K Or Original A5L/Copy paper A4L Image Repeat-Repeating An Image Over The Entire Copy100 Press the ↓Next key until Image Repeat is displayed 101 Original A5K/Copy paper A4L Or Original A5L/Copy paper A4KSelect Image Repeat with the keys. Then, press the OK key Set your original, then press the Start key Deleting The Stored Images Storing The ImagesPrinting a List Of The Stored Images Recalling The Stored Images To overwrite images already stored Storing The Images103 Press the ↓Next key until Archive File is displayed 104 Press the Menu key Press the Delete key Deleting The Stored Images105 106 Printing a List Of The Stored ImagesPress the List key Keys 107 Recalling The Stored ImagesPress the ↓Next key until the Ar- chive File is displayed Enter the number of copies with the Number keys 108 Combination Chart 109 Combination Chart 110 111 If Your Machine does not Operate AS YOU WantMessage 112 Display 113 If YOU Cannot Make Clear Copies 114 115 If YOU Cannot Make Copies AS YOU Want 116 Adjust Image 117 Combine 118 Duplex Square the paper and set it in the tray Loading Paper119 120 Loading Paper In The LargeCapacity Tray 121 Adding Toner 122 123 124 Clearing Misfeeds 125 126 When D is lit 127 When C is lit 128 When R is lit 129 130 When P is lit 131 When Z is lit Changing the Paper Size Adjust the back fence to the new paper size132 Fasten the fences with screws 133 To adjust the paper size 134 Sheet Finisher Adding Staples 135 136 137 138 139 Removing Jammed Staples 140 141 142 143 Pull out the punch waste box and remove punch waste Reinstall the punch waste box144 Enter 2 with the Number key Accessing the User Tools Copy Features145 146 Exiting From User Tools 147 148 User Tools Menu Copy Features 149 User Tools Menu Copy Features 150 Settings YOU can Change with the User ToolsGeneral Features 1/4 151 152 General Features 153 Default 1-Sided → 1-Sided 154 155 Adjust Image 1/2 156 157 Adjust Image 2/2 158 159 160 Input/Output 1/2 161 162 Input/Output 2/2 163 164 Shortcut Keys 165 DOS and Donts Machine Environment Where to PUT Your MachineOptimum environmental conditions Environments to avoid 167 Power Connection 168 Access To Machine Cleaning The Document Feeder Cleaning The Platen CoverCleaning the machine Maintaining Your Machine 170 Mainframe Non-reproduction area Copy paper weightFirst copy time Copying speed Type 1 and Type Continuous copying count Reproduction ratioCopy paper capacity 173 Dimensions W × D × H up to exposure glass Power consumptionSpace for main frame W × D 174 175 WeightNoise Emission Document Feeder Option Available paper size Paper Tray Unit OptionPaper capacity 177 178 Internal Tray 2 1 BIN Tray OptionNumber of bins Available paper size Sheet Finisher Option 180 181 Paper size 2 holes version Punch KIT OptionPaper size 3 holes version 182 183 Large Capacity Tray LCT Option 184 Power consumption MaxDuplex Unit Option 185 Bypass Tray Option 186 MB Copier Memory Unit Electric Sort KIT OptionMemory capacity Additional functions Originals scanned Copier Hard Disk Image Enhance KITOriginals stored for Archive File function Additional function 188 IndexNumerics 189 190 Means Power ON. c means Stand by A2328651 Errata 340/350/450 Operating Instructions