Safety Instructions For Miter Saw | RIDGID MS1290LZ specs

Safety Instructions For Miter Saw

Safety is a combination of common sense, staying alert and knowing how your miter saw works. Read this manual to understand this miter saw.

Safety Signal Words

DANGER: means if the safety infor- mation is not followed someone will be seriously injured or killed.

WARNING: means if the safety infor- mation is not followed someone could be seriously injured or killed. CAUTION: means if the safety infor- mation is not followed someone may be injured.

Before Using The Saw

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead-based paints,

•Crystalline silica from bricks and cement and other masonry products, and

•Arsenic and chromium from

chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well venti- lated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

WARNING: To reduce the risk of mistakes that could cause seri- ous, permanent injury, do not plug the miter saw in until the fol- lowing steps have been satisfac- torily completed.

•Completely assemble and align saw. (See “Assembly” and “Align- ment” sections within.)

•Learn the use and function of the ON-OFF switch, upper and lower blade guards, miter lock lever, bevel lock lever, cover plate stop screw, depth adjustment clamp and head

hold down, fence slide lock knobs and workpiece clamp. (See “Get- ting to Know Your Miter Saw” sec- tion within.)

•Review and understand all safety instructions and operating proce- dures in this manual.

•Review the maintenance methods for this miter saw. (See “Mainte- nance” section within).

Find and read the following labels on the miter saw.

3

Image 3

RIDGID MS1290LZ manual Safety Instructions For Miter Saw, Safety Signal Words Before Using The Saw

Contents

Page Table of Contents Safety Signal Words Before Using The Saw Safety Instructions For Miter Saw Safety Instructions for Miter Saws When Installing Or Moving The Miter SawBefore Each Use Plan Ahead To Protect Your Eyes, Hands, Face and Ears Keep Guards In Place, in workingTo Reduce the Risk of Accidental Preparing to Make Cut Dress For Safety Don’t Overreach. Keep good foot- ing and balance Whenever Saw Is Running Before Leaving The Saw Glossary of Terms for Woodworking Motor Specifications and Electrical Requirements Polarized Plug Motor Safety ProtectionWire Sizes Extension Cord Wire Sizes Length Unpacking and Checking Contents Getting to Know Your Miter Saw Saw at a desired bevel angleTop Carrying Handle Convenient way to transport saw Fit 1/4 hex end of combination tool AssemblyInstalling or Removing the Blade Stop Screw Arbor Be sure the arbor lock is released so the blade turns freely Workpiece Clamp Installation Four Basic Saw ControlsAssembling Dust Bag Bevel Lock Lever Bevel Index Pin Depth Adjustment Cam Knob Loosen the top two gib screws Alignment AdjustmentsStep Two Slide Tube Adjustment Step One Repositioning Zero Clear- ance Blade Insert Step Three Blade Square to Fence Miter Alignment Adjust Miter Scale Indicator Adjust Bevel Scale Indicator Step Four Blade Square to Table Bevel Adjustment Miter Lock Lever Adjustment To check, follow these stepsMiter Lock Lever Nut Lock Bevel Lock Lever AdjustmentBevel Pivot Movement/Adjustment Loosen the top locking jam nut Work Bench Applications Mounting The Miter SawGrip of the plastic handle. Car Portable Applications Check Damaged Parts. Check for Safety Instructions for Basic Saw Operations Reduce the Risk of Accidental Safety Instructions for Basic Saw Operations con’t Inspect Your Workpiece. Make sure Preparing to Make the Cut Make workshop child-proof. Install Basic Saw Operations Body and Hand Position Chop Cutting Miter Scale Usage Miter CutBevel Cut Sliding Fence Compound Cut Box Cutting Bowed MaterialCompound Cut Cutting Compound Miters on Picture Frames and Boxes Workpiece Clamp Usage Always perform dry runs. Make Completely set up your sawWorkpieces. Avoid binding Work against the blade Auxiliary Fence Workpiece Support Cut These Grooves With Saw Use a Chisel to Rough Cutting a DadoCutting Base Moldings Cut the two outside grooves Cutting Crown Moldings Two Methods of Cutting Crown MoldingCutting Crown Molding Flat on the Miter Saw Table Making a crown molding support jig Cutting Crown Molding Angled to the Table and Fence Wall Wall to Crown Molding Angle 45 degrees Laser System Mounting the Laser SystemCoverplate Stop Screw Arbor Blade Arbor Lock Spindle Keep these items for use if Laser system is removed Left Hand Thread Supplied withExactline Supplied with Inner Blade Broken Red Line Operation Replace the back cover and secure with two Phillips screws Changing Batteries Maintenance and Lubrication Maintenance Replacing Carbon BrushesLower Blade Guard Infrequent Lubrication as Required LubricationMotor Belt Tension Ball Bearings Prohibited Accessories AccessoriesUsing Carbide Tipped Blades Recommended Accessories Troubleshooting Guide Problem Probable Cause Suggested Corrective ActionGeneral Wiring Diagram Trouble Shooting of Brake by Qualified Service Person OnlyMotor Page Repair Parts ‡ Caution See mechanical assembly caution on Always order by part number not by key numberStandard Hardware Item May be purchased locally Base/Table Assembly Table Assembly Base Assembly Pivot Assembly Tube Pivot Assembly Pivot Sub Assembly Arm Guard Assembly ‡ Lower Guard Assembly ‡ Motor Assembly Page Form No. SP6505 RIDGID,INCPart No. SP6505 Catalog No. MS1290LZ Model No. MS1290LZ0Serial No