Mounting the Laser System | RIDGID MS1290LZ specs

Laser System

Mounting the Laser System

WARNING: To reduce the risk of injury from unexpected starting, unplug the saw whenever you are removing or installing the blade.

NOTE: See “Installing or Removing Blade” section of this manual for more information.

1.Unplug the saw from the outlet.

2.Rotate the lower plastic guard by hand. Loosen, but do not remove, the cover plate stop screw using the Phillips end of combination wrench.

3.Lift the lower guard up and tilt the lower guard assembly back so the arbor screw is exposed.

4.Find the arbor lock between the upper guard and the miter saw handle. Fit 1/4" hex end of combination tool in arbor screw or use 1/2" box end wrench.

5.Press the arbor lock and hold it firmly while turning the wrench clockwise. The arbor lock will engage after some turn- ing of the wrench.

NOTE: The arbor screw has a left hand

thread. This helps prevent unwanted loosening of the arbor screw during nor- mal operation.

Coverplate

Stop

Screw

Arbor

Screw

Blade

			n
		e
	s
	o
L	o
L

Arbor Lock

38

Image 38

RIDGID MS1290LZ manual Mounting the Laser System, Coverplate Stop Screw Arbor Blade Arbor Lock

Contents

Page Table of Contents Safety Instructions For Miter Saw Safety Signal Words Before Using The Saw Before Each Use Safety Instructions for Miter SawsWhen Installing Or Moving The Miter Saw To Reduce the Risk of Accidental Plan Ahead To Protect Your Eyes, Hands, Face and EarsKeep Guards In Place, in working Dress For Safety Preparing to Make Cut Whenever Saw Is Running Don’t Overreach. Keep good foot- ing and balance Glossary of Terms for Woodworking Before Leaving The Saw Motor Specifications and Electrical Requirements Extension Cord Wire Sizes Length Motor Safety ProtectionWire Sizes Polarized Plug Unpacking and Checking Contents Top Carrying Handle Convenient way to transport saw Getting to Know Your Miter SawSaw at a desired bevel angle Stop Screw Arbor AssemblyInstalling or Removing the Blade Fit 1/4 hex end of combination tool Be sure the arbor lock is released so the blade turns freely Assembling Dust Bag Workpiece Clamp InstallationFour Basic Saw Controls Bevel Lock Lever Bevel Index Pin Depth Adjustment Cam Knob Step One Repositioning Zero Clear- ance Blade Insert Alignment AdjustmentsStep Two Slide Tube Adjustment Loosen the top two gib screws Adjust Miter Scale Indicator Step Three Blade Square to Fence Miter Alignment Step Four Blade Square to Table Bevel Adjustment Adjust Bevel Scale Indicator Miter Lock Lever Miter Lock Lever AdjustmentTo check, follow these steps Loosen the top locking jam nut Bevel Lock Lever AdjustmentBevel Pivot Movement/Adjustment Nut Lock Portable Applications Mounting The Miter SawGrip of the plastic handle. Car Work Bench Applications Safety Instructions for Basic Saw Operations Check Damaged Parts. Check for Safety Instructions for Basic Saw Operations con’t Reduce the Risk of Accidental Preparing to Make the Cut Inspect Your Workpiece. Make sure Make workshop child-proof. Install Basic Saw Operations Chop Cutting Body and Hand Position Sliding Fence Miter CutBevel Cut Miter Scale Usage Cutting Compound Miters on Picture Frames and Boxes Cutting Bowed MaterialCompound Cut Compound Cut Box Work against the blade Completely set up your sawWorkpieces. Avoid binding Workpiece Clamp Usage Always perform dry runs. Make Workpiece Support Auxiliary Fence Cut the two outside grooves Rough Cutting a DadoCutting Base Moldings Cut These Grooves With Saw Use a Chisel to Cutting Crown Molding Flat on the Miter Saw Table Cutting Crown MoldingsTwo Methods of Cutting Crown Molding Cutting Crown Molding Angled to the Table and Fence Making a crown molding support jig Wall Wall to Crown Molding Angle 45 degrees Coverplate Stop Screw Arbor Blade Arbor Lock Laser SystemMounting the Laser System Supplied with Inner Blade Left Hand Thread Supplied withExactline Spindle Keep these items for use if Laser system is removed Operation Broken Red Line Changing Batteries Replace the back cover and secure with two Phillips screws Lower Blade Guard Maintenance and LubricationMaintenance Replacing Carbon Brushes Ball Bearings LubricationMotor Belt Tension Infrequent Lubrication as Required Recommended Accessories AccessoriesUsing Carbide Tipped Blades Prohibited Accessories General Troubleshooting GuideProblem Probable Cause Suggested Corrective Action Motor Wiring DiagramTrouble Shooting of Brake by Qualified Service Person Only Page Repair Parts Standard Hardware Item May be purchased locally ‡ Caution See mechanical assembly caution onAlways order by part number not by key number Base/Table Assembly Table Assembly Base Assembly Pivot Assembly Tube Pivot Assembly Pivot Sub Assembly Arm Guard Assembly ‡ Lower Guard Assembly ‡ Motor Assembly Page Catalog No. MS1290LZ Model No. MS1290LZ0Serial No RIDGID,INCPart No. SP6505 Form No. SP6505