22
Chapter 1 Selecting and Playing a Sound

Rhythm Sets

Rhythm Set Rhythm Set Bank Select Program
Group Number Number Number
MSB LSB
USER 1, 2, 3, 4 86 00 1, 2, 3 , 4
PR-A 001, 002 86 64 001, 002
PR-B 001, 002 86 65 001, 002
PR-C 001, 002 86 66 001, 002
PR-D 001, 002 86 67 001, 002
PR-E 001, 002 86 68 001, 002
PR-F 001, 002 86 69 001, 002
PR-G 001, 002 86 70 001, 002
CD-A 1, 2, 3, 4 86 32 1, 2, 3, 4
: ::::
CD-H 1, 2, 3, 4 86 39 1, 2, 3, 4
XP-A *1 *1 *1 *1
: ::::
XP-H *1 *1 *1 *1
* 1 Depends on the Wave Expansion Board installed.
Fixed Bank Select numbers are assigned to the Wave
Expansion Board itself.
Rhythm Set Rhythm Set Bank Select
Group Number Number
MSB LSB
SR-JV80-01 001–128 88 00
SR-JV80-01 129–256 88 01
SR-JV80-02 001–128 88 02
SR-JV80-02 129–256 88 03
:
SR-JV80-65 001–128 90 00
SR-JV80-65 129–256 90 01
In Performance mode
1. Press [PERFORM], getting its indicator to light.
2. Set the transmission channel of your external MIDI
device to match the XV-5080’s Performance Control
Channel (p. 212).
To learn about the MIDI settings of your external MIDI
device, see its owner’s manual.
3. Transmit the appropriate Bank Select MSB (Controller
#0) value to the XV-5080.
4. Transmit the appropriate Bank Select LSB (Controller
#32) value to the XV-5080.
5. Transmit the Program Change value.
The desired Performance will be selected.
* When the XV-5080 receives a Program Change message
without Bank Select messages, the corresponding Performance
in the currently selected group or bank will be chosen.
You can select any Performance Part’s Patch or Rhythm Set
via MIDI. To learn how, refer to “Assigning a different Patch
to Part (p. 162)” in the XV-5080 QUICK START.
The Performances in each group correspond to the Bank
Select numbers as follows.

Performances

Performance Performance Bank Select Program
Group Number Number Number
MSB LSB
USER 001–064 85 00 001–064
PR-A 001–032 85 64 001–032
PR-B 001–032 85 65 001–032
CD-A 001–064 85 32 001–064
:::::
CD-H 001–064 85 39 001–064
When Patch/Rhy Rx Ch and Perform Ctrl Ch are set to the
same channel, both Bank Select and Program Change are
sent, making it possible to switch among Patches, Rhythm
Sets, and Performances.
Using MIDI to Switch between Patch, Performance and General MIDI 2 Modes
You can switch between Patch, Performance, and General
MIDI 2 modes by transmitting the appropriate System
Exclusive (Sys Ex) message to the XV-5080, as listed below.
(Sys Ex messages are constructed using hexadecimal
notation.)
To switch to Patch/Rhythm Set (Sys Ex.)
F0 41 10 00 10 12 00 00 00 00 01 7F F7
To switch to Performance
F0 41 10 00 10 12 00 00 00 00 00 00 F7
To switch to GM2 mode
F0 41 10 00 10 12 00 00 00 00 03 7F F7
The third byte of the MIDI message indicates the device ID
number, and the factory setting is “10.” (This is “10” in
hexadecimal notation; in decimal this would be 16.) (This
device ID number will appear as 17 in the display of the XV-
5080. The transmitted messages will use a value of one less
than this (16).) If you have modified the device ID number (p.