5
IMPORTANT NOTES
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2
and 3, please read and observe the following:

Power Supply

Do not use this unit on the same power circuit with any
device that will generate line noise (such as an electric
motor or variable lighting system).
Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.

Placement

This device may interfere with radio and television
reception. Do not use this device in the vicinity of such
receivers.
Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
Excessive heat can deform or discolor the unit.
To avoid possible breakdown, do not use the unit in a wet
area, such as an area exposed to rain or other moisture.

Maintenance

For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.

Repairs and Data

Please be aware that all data contained in the units
memory may be lost when the unit is sent for repairs.
Important data should always be backed up Memory
Card, or written down on paper (when possible). During
repairs, due care is taken to avoid the loss of data.
However, in certain cases (such as when circuitry related
to memory itself is out of order), we regret that it may not
be possible to restore the data, and Roland assumes no
liability concerning such loss of data.

Memory Backup

This unit contains a battery which powers the units
memory circuits while the main power is off. When this
battery becomes weak, the message shown below will
appear in the display. Once you see this message, have the
battery replaced with a fresh one as soon as possible to
avoid the loss of all data in memory. To have the battery
replaced, consult with your retailer, the nearest Roland
Service Center, or an authorized Roland distributor, as
listed on the Information page.
Battery Low

Additional Precautions

Please be aware that the contents of memory can be
irretrievably lost as a result of a malfunction, or the
improper operation of the unit. To protect yourself against
the risk of loosing important data, we recommend that
you periodically save a backup copy of important data
you have stored in the units memory, a memory card.
Unfortunately, it may be impossible to restore the contents
of data that was stored in the units memory, a memory
card, or another MIDI device (e.g., a sequencer) once it has
been lost. Roland Corporation assumes no liability
concerning such loss of data.
Use a reasonable amount of care when using the units
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
Never strike or apply strong pressure to the display.
When connecting / disconnecting all cables, grasp the
connector itselfnever pull on the cable. This way you
will avoid causing shorts, or damage to the cables
internal elements.
A small amount of heat will radiate from the unit during
normal operation.
To avoid disturbing your neighbors, try to keep the units
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
The display screens printed in this owners manual are based
on the factory settings. However, please be aware that in
some cases they may differ from the actual factory settings.

Before Using Cards

Using DATA Cards

Carefully insert the DATA card all the way inuntil it is
firmly in place.
Insert memory cards with the gold contacts facing
downwards.
Never touch the terminals of the DATA card. Also, avoid
getting the terminals dirty.