OW N E R ’S OP E R A T I N G MA N U A L
CW-42HD CW-50XA CW-61
Flat Panel Plasma Display Monitor with
Page
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY
THREE YEAR LIMITED WARRANTY
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY
For Plasma Displays
CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE
EFFECTIVE WARRANTY DATE
IMPORTANT -- WARRANTY REGISTRATION
RIGHTS, LIMITS AND EXCLUSIONS
RUNCO VIDEO-PRODUCT INFORMATION
ADDITIONAL INFORMATION
RUNCO INTERNATIONAL, INC Attn Customer Service Department
RETAIN THIS INFORMATION FOR YOUR RECORDS
Safety Precautions
DOC Compliance Notice
Safety Precautions
Table of Contents
THREE YEAR LIMITED WARRANTY
Installation
Specifications
Table of Contents
Maintenance and Troubleshooting
Operation
List of Figures
Runco CinemaWall Owner’s Operating Manual
List of Figures
Runco CinemaWall Owner’s Operating Manual
Target Audience
1. Introduction
1.1 About This Manual
If You Have Comments
DANGER appears when a given action can cause severe injury or
1.2 Using This Manual
certain features
DANGER
1.3 Description, Features and Benefits
Key Features and Benefits
Use the safety fittings to fasten the CinemaWall to a wall when
Optional Accessories
2. REMOTE CONTROL SENSOR
Controls and Indicators
Figure 2-1. CinemaWall Controls and Indicators 1. POWER BUTTON
3. POWER/STANDBY INDICATOR
Connectors
6. VOLUME DOWN and UP
The Power on/off switch does not disconnect the plasma display
5. LEFT/- and RIGHT/+
2. EXTERNAL SPEAKER OUTPUTS
Figure 2-3. CW-50XA and CW-61 Connector Panel
1. POWER INPUT 100 to 240 VAC
3. VIDEO1, 2 RCA, S-Video
7. DVD/HD3, DVD/HD4 HDMI
2.2 CinemaWall Remote Control
Figure 2-4. CW-42HD and CW-50XA Remote Control
8. EXTERNAL CONTROL 9-pin, male D-Sub
3. MENU
1. IR OUTPUT INDICATOR
2. ON/OFF
4. Cursor Keys
3. +
Figure 2-5. CW-61 Remote Control 1. LIGHT
2. POWER ON/OFF
4. ASPECT
11. MUTE
10. VOLUME +
14. OFF TIMER
12. / EXIT
Controls and Functions
Runco CinemaWall Owner’s Operating Manual
Notes on Remote Control
3. Installation
3.1 Remote Control
Notes on Batteries
Installation
other surfaces
The signal from the remote control can be reflected by walls or
Installation should be performed by a qualified custom video
3.2 Quick Setup
Table 3-1. Installation Overview
installation specialist
Mounting the CinemaWall
Installation
Considerations
on a Wall or Table Stand
Other Considerations
Ventilation
Figure 3-2. Ventilation Requirements for Enclosure Mounting
prolong operating life
Connections to the
Connecting the
Figure 3-3. CinemaWall Connection Diagram
CinemaWall
Refer to Computer/Video Signal Compatibility on page 52 for
video quality because the signal is carried in the digital domain
throughout the entire signal path, from source component output
a list of computer signals compatible with the CinemaWall. Use
Figure 3-4. RS-232 Control System Connection
RS-232 Controller
Connection
Installation
Figure 3-5. Installing the Cable Clamps
Cable Management
Installation
Runco CinemaWall Owner’s Operating Manual
4. Operation
4.1 Turning on the Power
Figure 4-1. Attaching the Ferrite Cores to the Power Cable
4.2 Changing the OSD Language
4.3 Setting the PC Display Properties
4.4 Using the On-Screen Menus
3. The CinemaWall supports 36-bit color 68.7 billion possible colors
Signal Info
Picture Adjust
Install
Audio
Picture Adjust
1. When you change a picture quality setting, save the change to a
Main Menu
Figure 4-3. Typical PLUGE Pattern for Adjusting Brightness
yellow
Figure 4-4. Typical Gray Bar Pattern for Adjusting Contrast
gray
cyan
cyan
gray
yellow
green
Figure 4-6. Typical Test Pattern for Adjusting Sharpness
You must set the Advanced OSD option in the Function menu to
EXIT RETURN
The FILM setting is similar to NORMAL but produces a brighter picture
Note input
Audio
You cannot assign two or more audio inputs to the same video
Image Options
Aspect Ratio
Table 4-1. Aspect Ratio Settings
Description
Language Refer to Changing the OSD Language on page
Install
is set to OFF
You must set the Advanced OSD option in the Function menu to
display is turned off, or turned on and not receiving a signal
SECAM This is the standard format used mainly in France and Russia
options in the Function menu
Table 4-2. Power Management Indications
Function
1. If the computer is turned off or not properly connected to the
the image size
when you turn on the Soften feature
Lum. Setting AUTO Orbiter AUTO1 Inverse OFF Image Sweep OFF
OFF The OSD is always displayed at the same position
Signal Info
Operation
Runco CinemaWall Owner’s Operating Manual
Table 5-1. Troubleshooting Chart
5. Maintenance and Troubleshooting
5.1 Troubleshooting Tips
Image Options on
Computer/Video Signal
Table 5-1. Troubleshooting Chart continued
Maintenance and Troubleshooting
Compatibility on
Table 6-1. Serial Commands
6.1 RS-232 Connection and Port Configuration
6.2 Serial Command Syntax
6. Serial Communications
Serial Communications
Runco CinemaWall Owner’s Operating Manual
Table 7-1. CinemaWall Specifications
7. Specifications
7.1 CinemaWall Specifications
Runco CinemaWall Owner’s Operating Manual
Weight with Stand Regulatory Approvals Limited Warranty
Table 7-1. CinemaWall Specifications continued
Specifications
Specifications are subject to change without notice
Specifications
Dimensions
Figure 7-1. CinemaWall Model CW-42HD Dimensions
CinemaWall
Specifications
Figure 7-2. CinemaWall Model CW-50XA Dimensions
252.34 801.14
Runco CinemaWall Owner’s Operating Manual
Figure 7-3. CinemaWall Model CW-61 Dimensions
Specifications
103.46
7.3 Computer/Video Signal Compatibility
Table 7-2. Computer/Video Signal Compatibility Chart
CW-50XA and CW-61 are scaled up or down to that resolution
Table 7-2. Computer/Video Signal Compatibility Chart continued
Specifications
Runco CinemaWall Owner’s Operating Manual
Specifications
Runco CinemaWall Owner’s Operating Manual
Page
RUMA-010975
rev 09-25-06
