OW N E R ’S OP E R A T I N G MA N U A L
CW-42HD CW-50XA CW-61
Flat Panel Plasma Display Monitor with
Page
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY
THREE YEAR LIMITED WARRANTY
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY
For Plasma Displays
IMPORTANT -- WARRANTY REGISTRATION
EFFECTIVE WARRANTY DATE
CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE
RIGHTS, LIMITS AND EXCLUSIONS
RUNCO INTERNATIONAL, INC Attn Customer Service Department
ADDITIONAL INFORMATION
RUNCO VIDEO-PRODUCT INFORMATION
RETAIN THIS INFORMATION FOR YOUR RECORDS
DOC Compliance Notice
Safety Precautions
THREE YEAR LIMITED WARRANTY
Table of Contents
Safety Precautions
Installation
Maintenance and Troubleshooting
Table of Contents
Specifications
Operation
Runco CinemaWall Owner’s Operating Manual
List of Figures
Runco CinemaWall Owner’s Operating Manual
List of Figures
1.1 About This Manual
1. Introduction
Target Audience
If You Have Comments
certain features
1.2 Using This Manual
DANGER appears when a given action can cause severe injury or
DANGER
Key Features and Benefits
1.3 Description, Features and Benefits
Optional Accessories
Use the safety fittings to fasten the CinemaWall to a wall when
Figure 2-1. CinemaWall Controls and Indicators 1. POWER BUTTON
Controls and Indicators
2. REMOTE CONTROL SENSOR
3. POWER/STANDBY INDICATOR
The Power on/off switch does not disconnect the plasma display
6. VOLUME DOWN and UP
Connectors
5. LEFT/- and RIGHT/+
1. POWER INPUT 100 to 240 VAC
Figure 2-3. CW-50XA and CW-61 Connector Panel
2. EXTERNAL SPEAKER OUTPUTS
3. VIDEO1, 2 RCA, S-Video
Figure 2-4. CW-42HD and CW-50XA Remote Control
2.2 CinemaWall Remote Control
7. DVD/HD3, DVD/HD4 HDMI
8. EXTERNAL CONTROL 9-pin, male D-Sub
2. ON/OFF
1. IR OUTPUT INDICATOR
3. MENU
4. Cursor Keys
2. POWER ON/OFF
Figure 2-5. CW-61 Remote Control 1. LIGHT
3. +
4. ASPECT
14. OFF TIMER
10. VOLUME +
11. MUTE
12. / EXIT
Runco CinemaWall Owner’s Operating Manual
Controls and Functions
3.1 Remote Control
3. Installation
Notes on Remote Control
Notes on Batteries
Installation
other surfaces
The signal from the remote control can be reflected by walls or
Table 3-1. Installation Overview
3.2 Quick Setup
Installation should be performed by a qualified custom video
installation specialist
Considerations
Installation
Mounting the CinemaWall
on a Wall or Table Stand
Figure 3-2. Ventilation Requirements for Enclosure Mounting
Ventilation
Other Considerations
prolong operating life
Figure 3-3. CinemaWall Connection Diagram
Connecting the
Connections to the
CinemaWall
throughout the entire signal path, from source component output
video quality because the signal is carried in the digital domain
Refer to Computer/Video Signal Compatibility on page 52 for
a list of computer signals compatible with the CinemaWall. Use
Connection
RS-232 Controller
Figure 3-4. RS-232 Control System Connection
Installation
Cable Management
Figure 3-5. Installing the Cable Clamps
Runco CinemaWall Owner’s Operating Manual
Installation
Figure 4-1. Attaching the Ferrite Cores to the Power Cable
4.1 Turning on the Power
4. Operation
4.2 Changing the OSD Language
4.3 Setting the PC Display Properties
3. The CinemaWall supports 36-bit color 68.7 billion possible colors
4.4 Using the On-Screen Menus
Install
Picture Adjust
Signal Info
Audio
Picture Adjust
1. When you change a picture quality setting, save the change to a
Main Menu
Figure 4-3. Typical PLUGE Pattern for Adjusting Brightness
gray
Figure 4-4. Typical Gray Bar Pattern for Adjusting Contrast
yellow
cyan
yellow
gray
cyan
green
Figure 4-6. Typical Test Pattern for Adjusting Sharpness
EXIT RETURN
You must set the Advanced OSD option in the Function menu to
The FILM setting is similar to NORMAL but produces a brighter picture
You cannot assign two or more audio inputs to the same video
Audio
Note input
Image Options
Aspect Ratio
Table 4-1. Aspect Ratio Settings
Description
is set to OFF
Install
Language Refer to Changing the OSD Language on page
You must set the Advanced OSD option in the Function menu to
SECAM This is the standard format used mainly in France and Russia
display is turned off, or turned on and not receiving a signal
Function
Table 4-2. Power Management Indications
options in the Function menu
1. If the computer is turned off or not properly connected to the
the image size
when you turn on the Soften feature
Lum. Setting AUTO Orbiter AUTO1 Inverse OFF Image Sweep OFF
OFF The OSD is always displayed at the same position
Signal Info
Runco CinemaWall Owner’s Operating Manual
Operation
5.1 Troubleshooting Tips
5. Maintenance and Troubleshooting
Table 5-1. Troubleshooting Chart
Image Options on
Maintenance and Troubleshooting
Table 5-1. Troubleshooting Chart continued
Computer/Video Signal
Compatibility on
6.2 Serial Command Syntax
6.1 RS-232 Connection and Port Configuration
Table 6-1. Serial Commands
6. Serial Communications
Runco CinemaWall Owner’s Operating Manual
Serial Communications
7.1 CinemaWall Specifications
7. Specifications
Table 7-1. CinemaWall Specifications
Runco CinemaWall Owner’s Operating Manual
Specifications
Table 7-1. CinemaWall Specifications continued
Weight with Stand Regulatory Approvals Limited Warranty
Specifications are subject to change without notice
Figure 7-1. CinemaWall Model CW-42HD Dimensions
Dimensions
Specifications
CinemaWall
Specifications
Figure 7-2. CinemaWall Model CW-50XA Dimensions
252.34 801.14
Specifications
Figure 7-3. CinemaWall Model CW-61 Dimensions
Runco CinemaWall Owner’s Operating Manual
103.46
Table 7-2. Computer/Video Signal Compatibility Chart
7.3 Computer/Video Signal Compatibility
Specifications
Table 7-2. Computer/Video Signal Compatibility Chart continued
CW-50XA and CW-61 are scaled up or down to that resolution
Runco CinemaWall Owner’s Operating Manual
Runco CinemaWall Owner’s Operating Manual
Specifications
Page
rev 09-25-06
RUMA-010975
