LS-10i Remote Control | Runco LS-10I manual

Controls and Functions

9.TRIGGER 2 (3.5-mm, mini phono jack)

Provides 12 (+/- 1.5) volt switched output for an anamorphic lens transport (if installed) or screen relays with 250mA current capacity and short protection.

10.TRIGGER 1

Provides 12 (+/- 1.5) volt switched output for an anamorphic lens transport (if installed) or screen relays with 250mA current capacity and short protection.

11.RS-232

A female, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system.

1.LIGHT

Press to illuminate the buttons.

2.ON / OFF

Use these buttons to turn the projector on or off.

3.Source Selection Buttons:

VID

Press to select Composite video input as the source.

1	LIGHT	ON		OFF	2
		ON		OFF
		SOURCE
3	VID	S-VID	HDMI 1	HDMI 2
3	HD 1	HD 2	HD 3
	INFO
		ENTER			4
		ENTER
	EXIT			MENU
5	BRT	CONT	COL	TINT
		PICTURE MEMORY			6
	CUST1	ISF	ISF	CUST2	6
	CUST1	NIGHT	DAY	CUST2
		NIGHT	DAY

2.3

LS-10i Remote Control

S-VID (S-Video)			ASPECT RATIO
		16:9	4:3	LBOX	VWIDE
Press to select the	7

S-Video input as the		CINEMA	1	2	VCINE
source.		3	4	5	6	8

HDMI 1 / HDMI 2		7	8	9	0

Press to select an HDMI
input.	9
		FOCUS	ZOOM	LENS

HD 1 / HD 2 / HD 3 Press to select the “HD 1,” “HD 2” or “HD 3” video input as the source. By default, these buttons are assigned to the COMPONENT 1,

COMPONENT 2 and RGB video inputs respectively; however, you can re-assign these buttons to other inputs.

You can also assign these buttons to the Picture-in-Picture (PIP) function. For more information, refer to HD 1 Key / HD 2 Key / HD 3 Key on page 66.

Runco LS-10i Installation/Operation Manual

9

Image 25

Runco LS-10I operation manual LS-10i Remote Control

Contents

LS-10i Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingExternal Control Table of Contents Xiv List of Figures List of Figures About This Manual Introduction If you need Turn to Using This Manual Format screen Description, Features and Benefits Optional Accessories LS-10i at a Glance Controls and FunctionsCursor Keys Press this button to show or hide the OSD menus Exhaust Vent Runco Logo Badge Rear Cover RGB LS-10i Rear Panel LS-10i Remote Control Memory Preset Buttons Picture Adjustment Buttons BRT BrightnessContrast COL Color 169 Aspect Ratio Selection ButtonsLbox Letterbox Vwide VirtualWide Controls and Functions Remote Control Installation IR Reception Angles Installation Overview Quick SetupStep Procedure For Details, Refer Projector Installation Options InstallationInstallation Type Considerations Throw Distance Ambient LightEstimating Throw Distance Throw Range Throw Ratio Inches, with LS-10i Lens Options and Throw Ratios NoteLens Option Lens Floor Installation Ceiling InstallationVertical and Horizontal Position Horizontal Lens Shift Example Only Package Contents Installing the Optional Anamorphic Lens MountFolded Optics Other Considerations Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the Screws Plate Installation Mounting the LS-10i Angle Adjusting the Projection Connections to the LS-10i Connector Panel Access Components to the LS-10i Connecting SourceHDMI/DVI Connections See Figure HDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etc Computer RGB Camcorder Gaming Console 10. Scart Source Connections DTV-Set-Top Box 11. Component Video Connections 12. Composite and S-Video Connections Camcorder Gaming Console Connection RS-232 Controller Trigger Output to External Connecting 12-VoltTheater Equipment +12V Trigger Input Connecting to AC Power Connecting an External IRReceiver Appropriate to your locale Focus Zoom Lens Shift Turning on the Power Primary Lens Adjustments Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture Orientation Installation See Figure Adjustment Installing and Adjusting the Anamorphic Lens Adjusting the Lens Position Installation Selecting An Input OperationSource Selecting An Aspect Ratio Selecting Video Memory Available Main and PIP Source Combinations Using Picture-In-Picture PIPPIP Input Source Main Using the On-Screen Menus LS-10i Main Menu 169 Aspect Ratio SettingsLetterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu LS-10i Advanced Menu Advanced PCE Color Gamut setting refer to Color Gamut, below Color X/y Color Gamut Values RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Red Gre en Yellow Cy anMagenta Blue 13. LS-10i System Menu 14. Input Enable Sub-Menu Top right 921x518 16. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and Troubleshooting Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting External Control RS-232 Connection Port Configuration Serial Command SyntaxSerial Communications Some key command examples Serial Command Key Names and IR CodesSwitch to next user memory Apply 169 aspect ratio Remote Button IR Code RS232 Keyname 0x08 = value Operations Control Commands Function Action on unit Operation Commands Values Serial Commands Color.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 Error Code LED Indication Description RS-232 Error Codes CEC Commands Supported by the LS-10i Using Hdmi CEC MessagesCEC Command List Opcode Value Inactive Source 0x9D CEC Version LS-10i Specifications SpecificationsLS-10i Specifications Proteus 1 None Proteus 2, 3, 4, 5 HDTV, EDTV, Sdtv Industry-Standard Specifications Home Theater Calibration SpecificationsSpecifications are subject to change without notice LS-10i Dimensions LS-10i Dimensions Supported Timings Supported Signal Timings by Input PAL-B/G Page 020-1075-00 Rev. a September