Manuals / Runco / Home Audio / Home Theater System

Runco LS-10I Mounting the LS-10i, Floor Mounting Upright, Ceiling Mounting, Inverted

Models: LS-10I

1 112

Download 112 pages 48.37 Kb

Page 43

3.5

Installation

There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another.

In typical front and rear screen installations, the projector can be mounted to a secure and level surface such as a table or cart. Carts are useful when moving a projector during a presentation or from site to site. If possible, lock the wheels when it’s in position to prevent it from being moved during a presentation.

3.5

Mounting the LS-10i

Floor Mounting (Upright)

For fixed installations, and for those that want the projector out of sight or have a limited			Ceiling Mounting
space for projector and audience, you can invert the LS-10i and suspend it from the			(Inverted)
ceiling using a specially-designed ceiling mount fixture.
	Note	Use only the Runco-approved ceiling mount kit designed for your
		projector.
Install the ceiling mount kit according to the instructions provided with it.
If you are ceiling-mounting an LS-10i with an anamorphic lens, perform these additional
steps to secure the plate Security Hooks to the ceiling (refer to Attaching the Security
Hooks on the previous page).
1.	Install ceiling hooks (not supplied) into the ceiling directly above the Plate Hooks. The
	ceiling hooks should be small enough to accept a Chain End but strong enough when
	installed to each support 40 pounds or more.
2.	Attach a Chain End to the Chain and then connect it to one of the ceiling hooks.
3.	Cut the Chain to a length equal to or slightly greater than the distance between the
	ceiling hook and the corresponding Plate Hook.
4.	Attach a Chain End to the other end of the Chain. Then, use the Chain to connect the
	ceiling hook and the Plate Hook.
5.	Repeat Steps 2 through 4 for the other ceilling hook/Plate Hook pair.
The projector can also be inverted and placed in an enclosure above and behind the			Installing the Projector in
viewing area. Install four feet on the inside bottom surface of the enclosure on which the			an Enclosure
projector can rest. A variety of materials can be used for this purpose (for example, rubber
crutch tips or turntable feet).

Runco LS-10i Installation/Operation Manual

27

Image 43

Runco LS-10I Mounting the LS-10i, Floor Mounting Upright, Ceiling Mounting, Inverted, Installing the Projector in

Contents

DLPTM Home Theater Projector LS-10iPage Length of Warranty RuncoCare Standard Two Year Limited WarrantyRuncoCare Standard Features Warranty CoverageWarranty Exclusions RuncoCare Claim ProcedureSub Pixel Policy Extended Service OptionsOther Terms and Conditions Effect of Local Law Online Product RegistrationLimitation of Implied Warranties Exclusion of DamagesImportant Safety Instructions DECLARATION OF CONFORMITY Compliance InformationIMPORTANT RECYCLE INSTRUCTIONS FCC PARTINDUSTRY CANADA ICES-003 PRODUCT DISPOSALRunco LS-10iInstallation/Operation Manual NotesRuncoCare Standard Two Year Limited Warranty Table of Contentsviii Floor Mounting Upright Specifications Maintenance and TroubleshootingExternal Control Notes Table of ContentsList of Figures List of Figures LS-10iService Menu7-1. LS-10iDimensions Runco LS-10iInstallation/Operation ManualIf You Have Comments 1. Introduction1.1 About This Manual Target AudienceDANGER 1.2 Using This Manualformat screen 1.3 Description, Features and BenefitsOptional Accessories MENU 2. Controls and Functions2.1 LS-10iat a Glance SOURCE•FRONT IR SENSOR •EXHAUST VENTINTAKE VENT •PROJECTION LENSFigure 2-2. LS-10iRear/Bottom/Top View Cable Opening Ceiling Mount Holes Adjustable Feet•ADJUSTABLE FEET Runco Logo Badge Rear Cover Lamp Module Cover1.HDMI 1 Digital HDMI 2 Digital 5.COMPONENT 1/SCART RCA connectorsLS-10iRear Panel Figure 2-3. LS-10iRear Panel11.RS-232 2.3 LS-10iRemote Control9.TRIGGER 2 3.5-mm,mini phono jack 10.TRIGGEREXIT 5.Picture Adjustment Buttons BRT Brightness6.Memory Preset Buttons CUST1 4.INFOVWIDE VirtualWide 7.Aspect Ratio Selection Buttons16:9 LBOX LetterboxNotes Runco LS-10iInstallation/Operation ManualControls and Functions Notes on Batteries 3. Installation3.1 Remote Control Notes on Remote Control OperationInstallation Figure 3-1.IR Reception AnglesRunco LS-10iInstallation/Operation Manual 3.2 Quick SetupTable 3-1.Installation Overview InstallationConsiderations InstallationTable 3-2.Projector Installation Options Installation TypeFigure 3-2.Estimating Throw Distance Ambient LightThrow Distance Estimating Throw DistanceThrow Range in InstallationNotes Vertical and Horizontal Ceiling InstallationFloor Installation Figure 3-3.Projector PlacementInstallation Figure 3-5.Horizontal Lens Shift Example OnlyFolded Optics Other Considerations 3.4 Installing the Optional Anamorphic Lens MountPackage Contents Figure 3-6.Folded OpticsAttaching the Transport Assembly Attachment Plate Runco LS-10iInstallation/Operation Manual Installation2. Position the attachment plate as shown here 2. DO NOT OVER-TIGHTENTHE SCREWS Assembly Attachment plateInstallation Runco LS-10iInstallation/Operation ManualAnamorphic Lens Transport Assembly •Pliers •Scissors •Ceiling Hooks not supplied Ceiling Mounting Installing the Projector in3.5 Mounting the LS-10i Floor Mounting UprightAngle Adjusting the ProjectionInstallation 3.6 Connections to the LS-10i Connector Panel AccessHDMI/DVI sources BD, DVD Connecting SourceComponents to the LS-10i HDMI/DVI Connections: See FigureInstallation ComputerRGB Camcorder Figure 3-9.RGBHV ConnectionsSync Figure 3-10.SCART Source ConnectionsInstallation Runco LS-10iInstallation/Operation ManualInstallation Figure 3-11.Component Video ConnectionsRCA-to-BNCadapter Runco LS-10iInstallation/Operation Manual VCR Camcorder Gaming ConsoleFigure 3-12.Composite and S-VideoConnections InstallationConnection RS-232ControllerFigure 3-13. RS-232Control System Connection Theater Equipment Connecting 12-Volt3.5-mmmini plug Trigger Output to ExternalFigure 3-15.External IR Receiver Connection Connecting an External IRConnecting to AC Power ReceiverPrimary Lens Adjustments 3.7 Turning on the Power 3.8Focus Zoom Lens Shift 3.9 Changing the OSD Language 3.10 Adjusting the Picture OrientationRear Projection Ceiling Mode Anamorphic Lens 3.11 Installing and Adjusting the Anamorphic LensInstallation and AdjustmentAdjusting the Lens Position Runco LS-10iInstallation/Operation Manual InstallationNotes 4.2 Selecting An Aspect Ratio 4.3 4. Operation4.1 Selecting An Input Source4.4 Using Picture-In-PicturePIP Advanced 4.5 Using the On-ScreenMenusService MainOperation Figure 4-2. LS-10iMain MenuTable 4-2.Aspect Ratio Settings Operation Table 4-2.Aspect Ratio Settings continuedOperation Table 4-2.Aspect Ratio Settings continuedAspect Note sub-menu You must enter a passcode to access the Save ISFBelow Black Above Black Operation Figure 4-6.Overscan Examples Operation Figure 4-7. Input Select Sub-MenuFigure 4-8. LS-10i Advanced Menu AdvancedStandard for your region Table 4-3.x/y Color Gamut Values Offset settings reduce the image brightness Figure 4-9. RGB Adjust Sub-MenuRunco LS-10iInstallation/Operation Manual Figure 4-10. Fine Sync Sub-MenuOperation Operation Figure 4-11. PCE Sub-MenuFigure 4-12.CIE 1931 Chromaticity Diagram Runco LS-10iInstallation/Operation Manual Figure 4-13. LS-10i System MenuOperation Figure 4-14. Input Enable Sub-Menu Screen-SafeArea DMD Area644x362 921x518Runco LS-10iInstallation/Operation Manual Figure 4-16.PIP Split-ScreenModeOperation Figure 4-17. LS-10i Control Menu Language Figure 4-18. LS-10i Service Menu •Lamp Hours •Custom 1 / Custom •ISF Day ENTEROperation 5.1 Lamp Replacement 5. Maintenance and TroubleshootingSupported Timings on 5.2 Troubleshooting TipsTable 5-1.Troubleshooting Chart Maintenance and TroubleshootingMaintenance and Troubleshooting Table 5-1.Troubleshooting Chart continuedRunco LS-10iInstallation/Operation Manual Runco LS-10iInstallation/Operation Manual Maintenance and Troubleshooting6.1 Serial Communications RS-232Connection and Port ConfigurationSerial Command Syntax 6. External ControlApply 16:9 aspect ratio Table 6-1.Serial Command Key Names and IR CodesSome key command examples Switch to next user memory0x1d 0x08 op <operation> <command>CR Table 6-2.Serial Commands Table 6-2.Serial Commands continued vert.pos Table 6-2.Serial Commands continued1.key Table 6-2.Serial Commands continuedpattern Table 6-2.Serial Commands continuedcal.text1 Table 6-2.Serial Commands continuedRunco LS-10iInstallation/Operation Manual msgboxDescription Table 6-3. RS-232Error CodesError Code LED IndicationTable 6-4.CEC Commands Supported by the LS-10i 6.2 Using HDMI CEC MessagesCEC Command List Inactive Source External ControlSpecifications 7. SpecificationsLS-10iSpecifications Table 7-1. LS-10iSpecificationsOperating Altitude Operating Humidity Dimensions Table 7-1. LS-10iSpecifications continuedSpecifications Power Requirements Operating TemperatureLimited Warranty Table 7-1. LS-10iSpecifications continuedSpecifications Weight without lens: Regulatory ApprovalsRunco LS-10iInstallation/Operation Manual 7.2 LS-10iDimensionsFigure 7-1. LS-10iDimensions SpecificationsRunco LS-10iInstallation/Operation Manual Table 7-2.Supported Signal Timings by Input7.3 Supported Timings SpecificationsPAL-60 SpecificationsPAL-B/G PAL-MPage 020-1075-00Rev. A September