Input Enable Sub-Menu | Runco LS-10I guide

Operation

Input Enable: To enable or disable selection of a source, choose Input Enable from the

System menu and press ENTER. This displays the Input Enable sub-menu, shown in

Figure 4-14.

Figure 4-14. Input Enable Sub-Menu

•HDMI 1/HDMI 2: Enables or disables the HDMI 1 and HDMI 2 sources.

•RGB: Enables or disables the RGB source.

•Comp 1/Comp 2: Enables or disables the Component 1 and Component 2 sources.

•Video: Enables or disables the Composite video source.

If either Component 1 or Video is enabled, SCART must be disabled.

Note

•S-Video:Enables or disables the S-Video source.

•SCART: Enables or disables the SCART RGBS source.

If SCART is enabled, both Component 1 and Video must be disabled.

Note

Runco LS-10i Installation/Operation Manual

63

Image 79

Runco LS-10I operation manual Input Enable Sub-Menu

Contents

LS-10i Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingExternal Control Table of Contents Xiv List of Figures List of Figures About This Manual Introduction If you need Turn to Using This Manual Format screen Description, Features and Benefits Optional Accessories Press this button to show or hide the OSD menus Controls and FunctionsLS-10i at a Glance Cursor Keys Exhaust Vent Runco Logo Badge Rear Cover RGB LS-10i Rear Panel LS-10i Remote Control COL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons Contrast Vwide VirtualWide Aspect Ratio Selection Buttons169 Lbox Letterbox Controls and Functions Remote Control Installation IR Reception Angles For Details, Refer Quick SetupInstallation Overview Step Procedure Considerations InstallationProjector Installation Options Installation Type Throw Distance Ambient LightEstimating Throw Distance Lens LS-10i Lens Options and Throw Ratios NoteThrow Range Throw Ratio Inches, with Lens Option Position Ceiling InstallationFloor Installation Vertical and Horizontal Horizontal Lens Shift Example Only Package Contents Installing the Optional Anamorphic Lens MountFolded Optics Other Considerations Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the Screws Plate Installation Mounting the LS-10i Angle Adjusting the Projection Connections to the LS-10i Connector Panel Access HDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etc Connecting SourceComponents to the LS-10i HDMI/DVI Connections See Figure Computer RGB Camcorder Gaming Console 10. Scart Source Connections DTV-Set-Top Box 11. Component Video Connections 12. Composite and S-Video Connections Camcorder Gaming Console Connection RS-232 Controller +12V Trigger Input Connecting 12-VoltTrigger Output to External Theater Equipment Appropriate to your locale Connecting an External IRConnecting to AC Power Receiver Focus Zoom Lens Shift Turning on the Power Primary Lens Adjustments Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture Orientation Installation See Figure Adjustment Installing and Adjusting the Anamorphic Lens Adjusting the Lens Position Installation Selecting An Aspect Ratio Selecting Video Memory OperationSelecting An Input Source Main Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations PIP Input Source Using the On-Screen Menus LS-10i Main Menu 169 Aspect Ratio SettingsLetterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu LS-10i Advanced Menu Advanced PCE Color Gamut setting refer to Color Gamut, below Color X/y Color Gamut Values RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Red Gre en Yellow Cy anMagenta Blue 13. LS-10i System Menu 14. Input Enable Sub-Menu Top right 921x518 16. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and Troubleshooting Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting External Control RS-232 Connection Port Configuration Serial Command SyntaxSerial Communications Apply 169 aspect ratio Serial Command Key Names and IR CodesSome key command examples Switch to next user memory Remote Button IR Code RS232 Keyname 0x08 = value Operations Control Commands Function Action on unit Operation Commands Values Serial Commands Color.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 Error Code LED Indication Description RS-232 Error Codes Opcode Value Using Hdmi CEC MessagesCEC Commands Supported by the LS-10i CEC Command List Inactive Source 0x9D CEC Version Proteus 1 None Proteus 2, 3, 4, 5 SpecificationsLS-10i Specifications LS-10i Specifications HDTV, EDTV, Sdtv Industry-Standard Specifications Home Theater Calibration SpecificationsSpecifications are subject to change without notice LS-10i Dimensions LS-10i Dimensions Supported Timings Supported Signal Timings by Input PAL-B/G Page 020-1075-00 Rev. a September