Samsung PPM42S2 4 5 , 6

Remove the fixing bolts from both sides (left and right) of the wall attachment panel. Lift and pull the

bottom of the display a small amount, to separate the insulation holder point from the bottom of the

wall attachment panel.

Lift the display and separate the insulation holder point from the groove on top of the wall attachment

panel.

1716

4 Remove four large screws from the rear side of the display.

5 Insert the bolts and insulations into the four screwholes as shown in the follow-

ing figure:

ŒBolt

´Insulation holder

6 Put the insulation rubber point protruding from the rear top of the display in

the groove on the top of the wall attachment panel. Lift up the display a little

bit so that the insulation rubber point at the bottom of the rear side of the

display is put in the groove at the bottom of the wall attachment panel.

(Do not lift the display with any pressure. The insulation rubber at the top may

be taken off. )

´

Œ

Separating the Display from the Wall Attachment Panel

´

Œ

Contents

Main 2 Warning! Important Safety Instructions 3 FOR COMMERCIAL USE ONLY Important Safety Information Thank You for Choosing Samsung FCC Information Setup Connection (Connecting Speakers / Receiver) Picture Control Sound Contro User Instructions Table of Contents Screen Image retention Cell Defect Altitude Page Front Panel Your New Plasma Display Panel Rear Panel Remote Control Buttons Remote Control 1 3 2 Wall Installation Instructions 1 Parts 3 2 4 5 6 Separating the Display from the Wall Attachment Panel Displaying Status Information Displaying Clock Turning the Monitor(PDP) On and Off Turning the Monitor(PDP) On and Off 2 1 Viewing the Menus and Displays Page 23 Connecting Speakers Connecting PDP and Speakers / Stand and Speakers 22 Connecting a VCR/Cable Box Videotape Playback: Picture Control Connecting a DVD/Set-Top Box 24 To Play DVD: To Watch DTV: Customizing the Picture 2 4 Using Automatic Picture Settings 2 ! Selecting the Sound Source (RGB mode) 2 3 Swapping the Contents of the PIP Image and Main Image (Video and S-Video mode) 1 2 3 Changing the Location of the PIP Image 2 3 Changing the Size of the PIP Image Changing the Screen Size Freezing the Picture (When entering the Video mode) Page Customizing the Sound 2 4 Using Automatic Sound Settings 2 Time Setting Using the Surround 2 Setting the Clock 2 4 3 2 Setting the Timers 6 5 4 8 Connecting PC and Operation Pin Configuration Setting up Your Monitor (Plug and Play) Connecting a PC to the PDP Connecting to a PC 4948 To watch the PC screen: How to Set up Your PC Software (Windows only) 53 After connecting the PDP to your PC, adjust the position of the screen if it is not well-aligned. 3 4 Adjusting the PC Screen Changing the Position of the Image 3 4 Enlarging the Image (Zoom) 4 3 Moving the Zoom Picture 2 Changing the Size of the Image 3 Picture Automatic Adjustment On/Off Picture Quality Adjustment Fine Tuning (Phase) 3 Frequency Adjustment Function Description 60 Power Saver (RGB mode only) State Normal Operation Power-saving Function Mode Selecting a Menu Language Setting the Multi Control 5 4 1 Digital Noise Reduction Auto Power On 2 64 65 Setting Up the Remote to Operate Your VCR, Cable box, or DVD players 1 2 Using the Panel Lock Setting up Your Remote Control 2 Multiple Display Control 7170 Introduction Installation Installation (Continue) Main Screen Beginning-Confirming the Port Beginning-Changing the Port Power Control Input Source Control Aspect Ratio Control-Video/S-Video Aspect Ratio Control-RGB1/RGB2 Time Control Settings Control-Picture Settings Control-Picture (RGB) Settings Control-Audio Settings Control-Image Lock 1 (RGB) Troubleshooting Settings Control-Image Lock2 (RGB) Page Troubleshooting 92 93 Identifying Problems Liquids Cabinet Specifications Memo 94 95