When PJ lamp replacement time is reached | Sanyo POA-PN02C specification

E-mail setting

●When PJ lamp replacement time is reached:

TITLE: Message from projector 10-03-2005 00:59

Projector Model Name: model name

TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

*The projector lamp has reached replacement time. Lamp replacement is required.

✐Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every power- on of the projector. This alert mail will not be sent when unchecking the mail sending condition "When PJ lamp replacement time is reached".

●When lamp corres. value reaches preselect use time:

TITLE: Message from projector 10-03-2005 00:59

Projector Model Name: model name

TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

*The accumulated lamp use time has reached 1200 hours. Prepare for the lamp replacement.

Free messages

✐The network unit sends a free message when the lamp use time (Corresponding value) reaches the preselected lamp use time. It can be used for preparation of the lamp replacement and the maintenance required.

ENGLISH

PJ-NET ORGANIZER OWNER'S MANUAL [PLV-80/75 Series]

37

Image 37

Sanyo POA-PN02C owner manual When PJ lamp replacement time is reached, When lamp corres. value reaches preselect use time

Contents

PJ-Net Organizer plus C PLV-80/75 Series POA-PN02C Federal Communication Commission Notice ComplianceModel Numbers POA-PN02C Trade Name Sanyo Responsible party Address English Contents Use of Serial Port ContentsPage Chapter Web Management function +p.25 Features Tion Multi-control func Tion +p.58 PDA restriction Operating environment of PJ-Net Organizer Package contains Before use PJ Camera Viewer software Safety ropeCamera mounting tool set Hook and loop fastener big Hook and loop fastener small Use of this manual Expression/AbbreviationTrademarks Preparation Chapter Installation Installation and network configuration p.18-24 Flow of installationSet up is complete Function of the network unit p.17 Name and function of each part Tighten two screws by using a coin etc Installation and network configurationConnector cover Screw cover Mounting Connection of LAN cable Configure the network Network configurationDefault network configuration is set as follows Confirmation of the network menu How to enter the numbers Configuration for IP Address/ Sub net/ Gateway*1/DNS*2Fixing the network configuration Completing of installation Displaying Network PIN code menu Network PIN code settingEntering the Network PIN code Fixing the Network PIN code How to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Select a display mode and login Login the setting page of the projectorTion p.20. The default IP address is Enter the IP address Main setting page in the Standard Mode display Display of main setting Main setting page in the Light Mode display How to use the settingExample of the Setting Text box setting Type of the setting palletPull-down menu setting Radio button setting Use of Battery Initial setting To 32 alphanumeric characters can be used for the password PJLink and password settingWhats PJLink? Auto setting Date and time settingManual setting When using the e-mail function Network configurationMum Setting Smtp server and administrator address Mail settingMenu and follow the below steps Tor Option selection for sending alert mail Registering and deleting E-mail addressesLength of message should be less than 256 characters Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reached Enter user name of the projector etc. optional Snmp settingEnter place of the projector optional Community Trap Check and delete the trap addressItem Description Up to 10 trap addresses can be registered Trap option Trap option setting Chapter Controlling the Projector PJ status Power control and status checkPJ temp Status Description About projector condition Input Controls System Input source Image adjustment Menu Sound PC adjustment Natural wide, True There may not be available Setting up the projectorTable below Sets the image top/bottom and left/right Full Zoom Normal Natural wide True Setting procedure Lamp Corres. Value ResetExecute button Store/free the settings Save the controls and settingsUp to 18 characters can be used for the Memo Load a control set Check the saved items How to set the timer Timer settingSet a day or date Change the event mode Check the timer eventsSet an execute time Select an event action Event Items Description Projector information Status Indication of the lamp status Multi-control Controlling and setting the multi-projectorsExample of multi control Start/stop the multi control Multi control setting Word None is displayed if not using the Memo func- tion Enter projector name or installed location etcRegister the projector Confirmation of registered projector Mode Operation Change the mode of the registered projectorStatus Setting all together Check & Change page in the light modeControlling all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Example Control examplesControlling AV equipment through network Equipment PJ3 PJ2 PJ1 Control Use of telnetPreparation When the word Hello is replied, login has been succeeded Control the projector with telnet Command Function Chapter Appendix Peer-To-Peer connection Examples of connectionTo another network Entrance hall Gateway Router installed in the network Active Script/JavaScript enable Web browser settingFlash Player enable Proxy setting Examples OS/Browsers ActiveX controls and plug-ins settingWindows XP Professional Internet Explorer Using proxy server Flash Player Add-on settingNot using proxy server Netscape Navigator JavaScript Setting Proxy setting Product specification Pin modular connector RJ-45 Port specificationMini DIN-8pin connector Projector setting Computer setting Why doesn’t the setting page appear in my web browser?Following causes are possible. Please check them How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Can I develop a driver to control external serial equipment? Why am I not receiving E-mail alert messages? Can I update the firmware of the network unit What are the rules for IP address assignment? What is the MAC address assigned to the network unit?MAC address is indicated on the case back as the below Ifff