What should I do when I forget the password?

Q&A

QHow can I install several projectors equipped with the network unit?

AInstall and configure network one by one to avoid the IP address collision each

other (☞ p.24).

To configure the IP address please see item "Network configuration" (☞ p.20).

QHow many projectors can I control with multi-control function?

AIt has been designed to control up to 100 sets but it depends on the network envi- ronment.

Password/Login

QWhat should I do when I forget the password?

ASelect "Network PIN code" sub menu from "Network" menu on the projector. For further information, please see item "Network PIN code setting" (+p. 22).

QCan I register the setting page as a web browser "Favorites" or

"Bookmarks"?

APlease add "Login" page to your "Favorites" or "Bookmarks". Do not add the speci-

fied setting page because it will not be able to perform the password authentica- tion correctly.

ENGLISH

PJ-NET ORGANIZER OWNER'S MANUAL [PLV-80/75 Series]

Page 83

Image 83

Sanyo POA-PN02C owner manual What should I do when I forget the password?

Contents

PJ-Net Organizer plus C PLV-80/75 Series POA-PN02C Address ComplianceFederal Communication Commission Notice Model Numbers POA-PN02C Trade Name Sanyo Responsible party English Contents Use of Serial Port ContentsPage Chapter Web Management function +p.25 Features Tion Multi-control func Tion +p.58 PDA restriction Operating environment of PJ-Net Organizer Package contains Before use Hook and loop fastener small Safety ropePJ Camera Viewer software Camera mounting tool set Hook and loop fastener big Trademarks Expression/AbbreviationUse of this manual Preparation Chapter Installation Function of the network unit p.17 Flow of installationInstallation and network configuration p.18-24 Set up is complete Name and function of each part Mounting Installation and network configurationTighten two screws by using a coin etc Connector cover Screw cover Connection of LAN cable Confirmation of the network menu Network configurationConfigure the network Default network configuration is set as follows Completing of installation Configuration for IP Address/ Sub net/ Gateway*1/DNS*2How to enter the numbers Fixing the network configuration Fixing the Network PIN code Network PIN code settingDisplaying Network PIN code menu Entering the Network PIN code How to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Tion p.20. The default IP address is Main setting page in the Standard Mode display Display of main setting Example of the Setting How to use the settingMain setting page in the Light Mode display Radio button setting Type of the setting palletText box setting Pull-down menu setting Use of Battery Initial setting Whats PJLink? PJLink and password settingTo 32 alphanumeric characters can be used for the password Manual setting Date and time settingAuto setting Mum Network configurationWhen using the e-mail function Tor Mail settingSetting Smtp server and administrator address Menu and follow the below steps Length of message should be less than 256 characters Registering and deleting E-mail addressesOption selection for sending alert mail Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reached Community Snmp settingEnter user name of the projector etc. optional Enter place of the projector optional Up to 10 trap addresses can be registered Check and delete the trap addressTrap Item Description Trap option Trap option setting Chapter Controlling the Projector PJ temp Power control and status checkPJ status Status Description About projector condition Input Controls System Input source Image adjustment Menu Sound PC adjustment Full Zoom Normal Natural wide True Setting up the projectorNatural wide, True There may not be available Table below Sets the image top/bottom and left/right Execute button Lamp Corres. Value ResetSetting procedure Up to 18 characters can be used for the Memo Save the controls and settingsStore/free the settings Load a control set Check the saved items Set a day or date Timer settingHow to set the timer Select an event action Check the timer eventsChange the event mode Set an execute time Event Items Description Projector information Status Indication of the lamp status Example of multi control Controlling and setting the multi-projectorsMulti-control Start/stop the multi control Multi control setting Confirmation of registered projector Enter projector name or installed location etcWord None is displayed if not using the Memo func- tion Register the projector Status Change the mode of the registered projectorMode Operation Controlling all together Check & Change page in the light modeSetting all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Equipment Control examplesExample Controlling AV equipment through network PJ3 PJ2 PJ1 Preparation Use of telnetControl When the word Hello is replied, login has been succeeded Control the projector with telnet Command Function Chapter Appendix To another network Examples of connectionPeer-To-Peer connection Entrance hall Gateway Router installed in the network Proxy setting Web browser settingActive Script/JavaScript enable Flash Player enable Internet Explorer ActiveX controls and plug-ins settingExamples OS/Browsers Windows XP Professional Not using proxy server Flash Player Add-on settingUsing proxy server Netscape Navigator JavaScript Setting Proxy setting Product specification Mini DIN-8pin connector Port specificationPin modular connector RJ-45 Following causes are possible. Please check them Why doesn’t the setting page appear in my web browser?Projector setting Computer setting How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Can I develop a driver to control external serial equipment? Why am I not receiving E-mail alert messages? Can I update the firmware of the network unit MAC address is indicated on the case back as the below What is the MAC address assigned to the network unit?What are the rules for IP address assignment? Ifff