Sanyo POA-PN02C guide

Use of telnet

3 When communication is established, the word "PASSWORD:" appears on the window. Type the login password (PIN code) for the projector and then press "Enter" key on the keyboard. If you do not set up the Network PIN code, just press "Enter" key.

When the word "Hello" is replied, login has been succeeded.

4 Type the commands from the key board to control the external equipment and then press "Enter" key for termination. For example, type "C00" and press "Enter" key.

*"C00" is a command to turn the projector on.

-The extra projector will be turned on.

To disconnect the communication, press "Ctrl" key and "]" key at the same time.

*1 Further instructions about the telnet application, please see the on-line guide on your computer. *2 The commands are defined by each product independently, so please consult the manufacturer

or sales dealer for further information of the commands.

*The password is a Network PIN code decided item "Network PIN code setting" (+p.22, 31). If the authentication of the entered password is failed 4 times continuously, the communication will be disconnected automatically. Please try again for the connection.

PJ-NET ORGANIZER

OWNER'S MANUAL [PLV-80/75 Series]

ENGLISH

69

Image 69

Sanyo POA-PN02C owner manual When the word Hello is replied, login has been succeeded

Contents

PJ-Net Organizer plus C PLV-80/75 Series POA-PN02C Federal Communication Commission Notice ComplianceModel Numbers POA-PN02C Trade Name Sanyo Responsible party Address English Contents Use of Serial Port ContentsPage Chapter Web Management function +p.25 Features Tion Multi-control func Tion +p.58 PDA restriction Operating environment of PJ-Net Organizer Package contains Before use PJ Camera Viewer software Safety ropeCamera mounting tool set Hook and loop fastener big Hook and loop fastener small Expression/Abbreviation Use of this manualTrademarks Preparation Chapter Installation Installation and network configuration p.18-24 Flow of installationSet up is complete Function of the network unit p.17 Name and function of each part Tighten two screws by using a coin etc Installation and network configurationConnector cover Screw cover Mounting Connection of LAN cable Configure the network Network configurationDefault network configuration is set as follows Confirmation of the network menu How to enter the numbers Configuration for IP Address/ Sub net/ Gateway*1/DNS*2Fixing the network configuration Completing of installation Displaying Network PIN code menu Network PIN code settingEntering the Network PIN code Fixing the Network PIN code How to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Select a display mode and login Login the setting page of the projectorTion p.20. The default IP address is Enter the IP address Main setting page in the Standard Mode display Display of main setting How to use the setting Main setting page in the Light Mode displayExample of the Setting Text box setting Type of the setting palletPull-down menu setting Radio button setting Use of Battery Initial setting PJLink and password setting To 32 alphanumeric characters can be used for the passwordWhats PJLink? Date and time setting Auto settingManual setting Network configuration When using the e-mail functionMum Setting Smtp server and administrator address Mail settingMenu and follow the below steps Tor Registering and deleting E-mail addresses Option selection for sending alert mailLength of message should be less than 256 characters Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reached Enter user name of the projector etc. optional Snmp settingEnter place of the projector optional Community Trap Check and delete the trap addressItem Description Up to 10 trap addresses can be registered Trap option Trap option setting Chapter Controlling the Projector Power control and status check PJ statusPJ temp Status Description About projector condition Input Controls System Input source Image adjustment Menu Sound PC adjustment Natural wide, True There may not be available Setting up the projectorTable below Sets the image top/bottom and left/right Full Zoom Normal Natural wide True Lamp Corres. Value Reset Setting procedureExecute button Save the controls and settings Store/free the settingsUp to 18 characters can be used for the Memo Load a control set Check the saved items Timer setting How to set the timerSet a day or date Change the event mode Check the timer eventsSet an execute time Select an event action Event Items Description Projector information Status Indication of the lamp status Controlling and setting the multi-projectors Multi-controlExample of multi control Start/stop the multi control Multi control setting Word None is displayed if not using the Memo func- tion Enter projector name or installed location etcRegister the projector Confirmation of registered projector Change the mode of the registered projector Mode OperationStatus Check & Change page in the light mode Setting all togetherControlling all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Example Control examplesControlling AV equipment through network Equipment PJ3 PJ2 PJ1 Use of telnet ControlPreparation When the word Hello is replied, login has been succeeded Control the projector with telnet Command Function Chapter Appendix Examples of connection Peer-To-Peer connectionTo another network Entrance hall Gateway Router installed in the network Active Script/JavaScript enable Web browser settingFlash Player enable Proxy setting Examples OS/Browsers ActiveX controls and plug-ins settingWindows XP Professional Internet Explorer Flash Player Add-on setting Using proxy serverNot using proxy server Netscape Navigator JavaScript Setting Proxy setting Product specification Port specification Pin modular connector RJ-45Mini DIN-8pin connector Why doesn’t the setting page appear in my web browser? Projector setting Computer settingFollowing causes are possible. Please check them How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Can I develop a driver to control external serial equipment? Why am I not receiving E-mail alert messages? Can I update the firmware of the network unit What is the MAC address assigned to the network unit? What are the rules for IP address assignment?MAC address is indicated on the case back as the below Ifff