Registering and deleting E-mail addresses | Sanyo SO-WIN-KF3AC

Chapter 6 Basic setting and operation

2Registering and deleting E-mail addresses

Click "Add E-mail address" and type the E-mail address onto the text box and click Set button. To check the registered addresses, click Check/Delete sub menu tab. The addresses are listed as the figure on the right.

✐Up to 10 E-mail addresses can be registered.

To delete the registered addresses, check the address you want to delete and click Delete button.

3Option selection for sending alert mail

Click Option sub menu tab. Check the condition items under which alert mail will be sent and click Set button.

Please refer to the item "Examples :Type and contents of alert mail" described on the next page.

Check / Delete

Option

56

[1]––––––––––––––––––––––––––––––––––

oWhen PJ lamp is off.

oWhen PJ lamp replacement time is reached.

oWhen internal PJ power circuit is failed.

oWhen internal PJ temperature is too high.

oWhen PJ is turned into Standby in proper user

operation.

[2]––––––––––––––––––––––––––––––––––

oWhen accumulated filter use time reaches

[ ] hours.

oWhen Power management function turns PJ lamp off.

oWhen the signal is interrupted.

oWhen Auto Play is failed.

[3]––––––––––––––––––––––––––––––––––

oWhen lamp Corres. Value reaches

[ ] hours. Attached message

✐If condition "When Auto Play is failed" is checked, the trap is sent when the error occurs during the auto display operation using with the network viewer function (+p.109). For further information of the

error, refer to item "Auto Display setting and control page [3]"(+p.124).

✐The length of message should be less than 255 characters.

✐Up to 99,999 hours can be set for use time.

Image 56

Sanyo SO-WIN-KF3AC, QXXAVC922---P Registering and deleting E-mail addresses, Option selection for sending alert mail

Contents

Network Set-up and Operation For Windows Federal Communications Commission Notice For Canadian UsersFCC Warning FCC RF Exposure Warning Bestimmungen der Richtlinie 1999/5/EG befindet Use of this manual Trademarks and CopyrightExpression/Abbreviation Table of contents 109 127 Required operating environment for computers 256MB or more for Windows 2000 or Windows XPRequired to support any of VGA 640 x 480, Svga Network Network specifications of the projector Chapter About LAN functions Flow of Image Transfer LAN functions and the featuresImage projecting system via LAN An example of the connection LAN connection modes Operate the computer mouse with the remote control About LAN functions Setup procedures Install the software on computers LAN and set the configurationNetwork Configuration has completed Select Wired LAN or Wireless LAN then connect Installing the software Network Viewer & Capture 5 installation Setup procedures Installed software Network CaptureNetwork Viewer 5 File Converter Network Viewer 5 Program Editor File Converter 2 installation Installed software and places Names and functions of the operation screen Network connection standby display Network Capture 5 window Parts Names and Functions of the Screen Using the multiple network adaptors Wired LAN configurations Connecting to the LAN line Network environment settings Description Confirming the operation Confirming the operation Network information Wired factory defaultNetwork PIN code Wired LAN factory default settings Selected LAN Wired LAN configurations Wireless LAN configurations Setting the network environment Setting procedures Identifier of the wireless access point WPA2-PSK are not available Configuring security with the projector Use of security type WEP Available PSK key characters Digits Easy wireless setting Setting Procedures Wireless factory default Computer environment and Wireless LAN connection Wireless indicator display Wireless LAN factory default settings Selected LAN Basic setting and operation Select a display mode and login Starting up the Browser Display of main setting Main setting page in the Standard Mode displaySetting Main menu How to use the setting Main setting page in the Light Mode displayExample of the Setting Setting Pallet Type of the setting pallet Text box settingPull-down menu setting Radio button setting Initial setting Switches PJLink password authentication on or offPassword for PJLink function Japanese Whats PJLink? Network PIN code settingPJLink and password setting Manual setting Date and time settingAuto setting Network configuration Setting of LANSelects LAN1 to LAN5 and Simple Sets Dhcp or Manual Basic setting and operation Configuring wireless LAN setting and security setting Configuring wireless LAN setting Configuring wireless LAN security setting ItemDescription Mail setting Setting Smtp server and administrator address Hours. Attached message Registering and deleting E-mail addressesOption selection for sending alert mail Examples Type and contents of alert mail When PJ lamp replacement time is reached When lamp corres. value reaches preselect use time Snmp setting Enter user name of the projector etc. optionalEnter place of the projector optional Community Up to 10 trap addresses can be registered Check and delete the trap addressPublic Trap option setting Basic setting and operation Controlling the projector PJ temp Power control and status checkPJ status About projector condition Status Description Controls Input System Image adjustment Image mode Video Computer Suppresses the sound Adjusts the sound volume from the speakersSound PC adjustment Setting up the projector Screen mode VideoTable below Normal True Wide Full Custom Sets Auto PC Adjustment mode Sets Auto Keystone modeSets the auto-input signal detection mode Standby mode Lamp counter resetting Reset the time after lamp replaced Set a day or date Timer settingHow to set the timer Check the timer events Change the event modeSet an execute time Select an event action Time Projector PowerEvent Projector information Items Description Indication of the lamp status Example of multi control Controlling and setting the multi-projectorsMulti-control Menu are linked to the main menu Start/stop the multi controlStops multi control function Register the projector Confirmation of registered projector Status Change the mode of the registered projectorMode Operation Check & Change page in the light mode Setting all togetherCheck & Change page in the light mode Controlling all together Viewer auto setting all together Network capture functions About Network Capture function Start up the Network CaptureReal Time Capture +p.89 Network Communication +p.94 Commands on the task bar Menu during Real time capturingMenu during Moderator function Menu during Network Communication Parameter set up Using the Real Time Capture Registering the computers Control by the computer Real time capturing operation Set enable or disable the real time capturingControl by the web browser Control by the projector Setting condition Example of advanced use Using the Network Communication PC6 Settings before using the Network Communication Menu tree Description of capture editing window Tool bar button names How to use the Network communication Setting of the drawing tool attribute Edit capture imageDrawing figures Erase drawn objects Letter attribute setting 100Drawing letter Set type face, style, size and effects of the font Network Communication operation and change of state 101Preparation On the Communication Executing the forcing mode 102 Moderator function 103Moderator Clients Preparation for using the moderator function Normal mode application windowModerator mode application window 104 Using the moderator function 105Description of application window Moderator operation 106 Moderators password setting upUnregister moderator status 107 Error informationError messages Cause and corresponding 108 Network Viewer functions 109 How to use the Network Viewer 5 File Converter Menu Command Tool ButtonCreating the available data Network Viewer 110 Command Tool Button Creating the available data111 Menu Sub Menu Description View Network Viewer functions Setting of output destination and conversion mode Conversion modeOutput destination 113 Select a folder and click Save button 115 Procedure of making programCreating a program file Program Editor 116 Displays the folder selection windowDeletes the folder path from the folder list Moves up the selected folder path Sub menu Description Setting up the display order and time of the images117 Added Moved Image frame on the index window118 Limitation of the Program file Example of the created program selection119 Condition to use the Network Viewer function Using the Network Viewer function120 121 Setup the setting page 1 of the Visual displaySetup the setting page 2 of the Selection Display 122 Means endless play Auto Display setting and control123 Error information Error type124 Description 125 Display time Repeat times 126 Appendix 127 Control Use of telnet128 Command Function 129 Web browser setting Active Script/JavaScript enableFlash Player enable Proxy setting ActiveX controls and plug-ins setting Windows XP Professional131 Examples OS/Browsers Flash Player Add-on setting Using proxy serverNot using proxy server 132 Netscape Navigator Flash Player Plug-in setting133 134 Firewall setting 135 Troubleshooting 136 Infrastructure Mode Should be same as the setting of the access pointNo setting is required. Automatically set as Dhcp 137 138 Cannot be turned on/off with the web browser 139 Speed of playing back images are very slow 140 Images from the file server don’t appear on the screen?Cannot make a new program file What kind of image formats can I convert? 141 Terminology 142 143 SO-WIN-KF3AC