Sanyo VDC-HD3300/HD300P, VDC-HD3100/HD3100P manual

Click NETWORK in the configuration menu to display the NETWORK SETTINGS screen. On this screen, configure the following settings as required.

AConfiguring basic network settings (NETWORK)

BConfiguring DDNS setting (DDNS)

CConfiguring HTTP settings

DConfiguring RTSP/RTP settings

EConfiguring access name settings (ACCESS NAME)

FMulticast settings (MULTICAST)

Required operation privilege: admin

Before attempting to configure these network settings, contact your network administrator.

Configure the environment required to connect to the camera via the network by specifying the IP address, subnet mask, and other information.

1 In [IP ADDRESS], select “FIX” and type the IP address of the camera below it.

2 In [SUBNET MASK] and [GATEWAY], type your subnet mask and gateway addresses, respectively.

3 In [DNS (PRIMARY)] and [DNS (SECONDARY)], type your primary and secondary DNS server addresses and click SET .

Because you selected “FIX” in [IP ADDRESS], you specify here fixed DNS server addresses.

After completing the above steps, click the Close button to once disconnect and then reconnect to the camera to apply the changes.

To redo the procedure from the beginning, before clicking SET , click CANCEL .

To restore the factory default settings, click DEFAULT .

In [MAC ADDRESS], the MAC address of the camera is shown. You cannot change this address.

Working with Administrator Configuration Screens 2/50

Image 50

Sanyo VDC-HD3300/HD300P, VDC-HD3100/HD3100P specifications Working with Administrator Configuration Screens 2/50

Contents

VDC-HD3300/HD300P VDC-HD3100/HD3100P Introduction1/15 Introduction 2/15 Introduction 3/15 HV/OFF Introduction 4/15 Introduction 5/15 ASSIST/IRIS Settings Introduction 6/15 Introduction 7/15 Alarm Input Terminal Connection Introduction 8/15 Connection to 12 VDC power supply Alarm Output Terminal ConnectionConnection to 24 VAC power supply Introduction 9/15 About the internet connection Using PoEIntroduction 10/15 Introduction 11/15 Introduction 12/15 Press the SET button for 2 seconds or more Adjusting focus Introduction 13/15 Press the NEAR/FAR button to adjust the iris level Introduction 14/15 Introduction 15/15 Quick Operation Guide1/10 Quick Operation Guide 2/10 Connect the power cable to the power terminalsConnect the network LAN socket to your PC using a LAN cable Turn on the camera Access the camera from your PCs Web browser Quick Operation Guide 3/10 Quick Operation Guide 4/10 Quick Operation Guide 5/10 Detect Quick Operation Guide 6/10 Quick Operation Guide 7/10 Quick Operation Guide 8/10 Quick Operation Guide 9/10 Optional Configuration Quick Operation Guide 10/10 Before You Begin Network Operation1/13 Assign a unique IP address to each camera Access the camera from your Web browserBefore You Begin Network Operation 2/13 Monitor live video Before You Begin Network Operation 3/13 Status Insert the supplied CD-ROM into the CD-ROM drive of your PC Click Auto IP SetupBefore You Begin Network Operation 4/13 Make changes to the camera data and click Execute Select the desired camera and click Manual settingBefore You Begin Network Operation 5/13 Before You Begin Network Operation 6/13 Click Network Connections Before You Begin Network Operation 7/13Control Panel, click Network and Internet Connections Before You Begin Network Operation 8/13 Click Properties Before You Begin Network Operation 9/13 Control Panel, click Network and Sharing Center Double-click Local Area Connection Before You Begin Network Operation 10/13Click Manage network connections Select the Internet Protocol Version 4 TCP/IPv4 check box Before You Begin Network Operation 11/13 Disabling authentication check at login Before You Begin Network Operation 12/13 Before You Begin Network Operation 13/13 Working with Live Screen1/10 Start Internet Explorer Type your user name and password and click OKWorking with Live Screen 2/10 Working with Live Screen 3/10 Working with Live Screen 4/10 Working with Live Screen 5/10 Other Buttons Working with Live Screen 6/10Menu Selection Buttons Working with Live Screen 7/10 Size Working with Live Screen 8/10 Click Close Working with Live Screen 9/10Click the Capture button on the tool panel Working with Live Screen 10/10 Starting alarm signal outputStopping alarm signal output Automatic Stop Working with Administrator Configuration Screens1/50 VDC-HD3300/HD300P VDC-HD3100/HD3100P Working with Administrator Configuration Screens 2/50 DDNS, select on Working with Administrator Configuration Screens 3/50IP ADDRESS, select Dhcp Working with Administrator Configuration Screens 4/50 Working with Administrator Configuration Screens 5/50 Http PORT, type your Http port number Working with Administrator Configuration Screens 6/50 Clock DISPLAY, select the clock display style Working with Administrator Configuration Screens 7/50TITLE, type the desired camera title and click SET Working with Administrator Configuration Screens 8/50 Working with Administrator Configuration Screens 9/50 Working with Administrator Configuration Screens 10/50 Working with Administrator Configuration Screens 11/50 Anonymous User LOG IN, select on and click SET Configure the image quality Picture Quality Working with Administrator Configuration Screens 12/50Configure the resolution Resolution When your selection in Priority is Bitrate Bitrate Working with Administrator Configuration Screens 13/50When your selection in Priority is Quality Picture Quality Frame RATE, select the frame rate of the stream Working with Administrator Configuration Screens 14/50 Working with Administrator Configuration Screens 15/50 Configuration Summary for Each Sub Menu Item Switching between Monitoring Conditions Working with Administrator Configuration Screens 16/50Configuring Monitoring Conditions Sense UP, select the electronic sensitivity boosting power Working with Administrator Configuration Screens 17/50 MASKING, select on and click SET White BALANCE, select AWC Working with Administrator Configuration Screens 18/50Click SET and then Back Working with Administrator Configuration Screens 19/50 Resize the center metering area Working with Administrator Configuration Screens 20/50BLC, select Center and click SET BLC, select Masking and click SET Working with Administrator Configuration Screens 21/50Click SET and then Back Working with Administrator Configuration Screens 22/50 Working with Administrator Configuration Screens 23/50 Working with Administrator Configuration Screens 24/50 DAY/NIGHT, select Auto Working with Administrator Configuration Screens 25/50Manually Configuring Mode-Switching Luminance Level ADJ Fixing Camera to Black-and-White Video Mode Working with Administrator Configuration Screens 26/50Fixing Camera to Color Video Mode GAMMA, select the gamma correction level and click SET Working with Administrator Configuration Screens 27/50Vivid Color EFFECT, select on and click SET Select the Manual check box Working with Administrator Configuration Screens 28/50DNR, select on and click SET Click ONE Push to focus on the subject Working with Administrator Configuration Screens 29/50MIRROR, select the desired mirror mode and click SET Click Privacy Mask in the sub menu COLOR, select the color of the mask patterns Working with Administrator Configuration Screens 30/50Select the Setting Items check box Working with Administrator Configuration Screens 31/50 Working with Administrator Configuration Screens 32/50 Working with Administrator Configuration Screens 33/50 Checking how the motion sensor works Working with Administrator Configuration Screens 34/50SENSITIVITY, select the detection sensitivity Working with Administrator Configuration Screens 35/50 Working with Administrator Configuration Screens 36/50 Working with Administrator Configuration Screens 37/50 Alarm Working with Administrator Configuration Screens 38/50 Alarm OUT1, select Remote Working with Administrator Configuration Screens 39/50 Configure your e-mail server Mail ADDRESS, type the recipient e-mail addresses Working with Administrator Configuration Screens 40/50AUTHENTICATION, select the authentication method To send a test e-mail, click Test If you selected Network Failure Working with Administrator Configuration Screens 41/50TRIGGER, select the e-mail transmission conditions If you selected Interval TEXT, type the message text and click SET Working with Administrator Configuration Screens 42/50SUBJECT, type the subject title of the e-mail Working with Administrator Configuration Screens 43/50 To use the passive FTP mode, in FTP PASSIVE, select USE Working with Administrator Configuration Screens 44/50 To use a temporary file, set Temporary File to USE Working with Administrator Configuration Screens 45/50 If you selected Alarm IN1/2, MOTION, or Alarm OUT1/2 Working with Administrator Configuration Screens 46/50 Working with Administrator Configuration Screens 47/50 Click SET Working with Administrator Configuration Screens 48/50Select the firmware updater file Working with Administrator Configuration Screens 49/50 Working with Administrator Configuration Screens 50/50 Access LOG A1/10 Cannot access the camera 2/10 3/10 Camera has been suddenly disconnected 4/10 Buttons on the control panel/tool panel do not respond 5/10 Cannot set Shutter to Short or Long 6/10 Cannot display Live video 7/10 Video image is distorted and cannot be displayed correctly 8/10 Live video image is noisy 9/10 E-mail transmission function does not work Upgrade has been terminated 10/10 Copyright Notice/How to Use This Manual1/8 Copyright Notice/How to Use This Manual 2/8 Copyright Notice/How to Use This Manual 3/8 Copyright Notice/How to Use This Manual 4/8 Main window Index windowTitle window Previous/Next End 3 ... a B C 123 Copyright Notice/How to Use This Manual 8/8