Before You Begin Network Operation 3/13 | Sanyo VDC-HD3300/HD300P

If you are installing two or more new cameras on the same local network, you need to change the factory default IP address of each camera to prevent IP address overlap. The supplied “Auto IP Setup” software frees you from this burden by automatically assigning a unique IP address to each camera on your network.

Before setting up the IP addresses automatically, click the [Search Cameras] button in the utility window to search all cameras on the network and display the address settings and details of each camera.

1 Status

NEW: The camera has the default IP address (“192.168.0.2”).

Assign a unique IP address.

OK: The camera has a unique IP address and can be connected successfully to network.

CAUTION: The camera cannot be connected successfully to the network because of IP address overlap or other reason.

Change the IP address.

2 Number of searched cameras (Total and by status)

3 Camera details

“Model name”, “IP Address”, “Port”, “SSL”, “Camera Title”, and “Firmware Version” are not shown if the network board or other hardware is not supported.

“IP Address”, “Port”, “SSL”, and “Camera Title” are editable. (Refer to the “Manually Setting Up IP Addresses of Existing Cameras” section.)

4 Camera Image button

Select the desired camera row and click this button. Then, video from the camera appears in a separate window. Use it to check which camera is selected or when editing the camera title or other data.

5 Web Browser button

Select the desired camera row and click this button. Then, the Web browser opens and connects to the camera automatically.

Before You Begin Network Operation 3/13

Image 28

Sanyo VDC-HD3300/HD300P, VDC-HD3100/HD3100P specifications Before You Begin Network Operation 3/13, Status

Contents

VDC-HD3300/HD300P VDC-HD3100/HD3100P Introduction1/15 Introduction 2/15 Introduction 3/15 HV/OFF Introduction 4/15 Introduction 5/15 ASSIST/IRIS Settings Introduction 6/15 Introduction 7/15 Alarm Input Terminal Connection Introduction 8/15 Alarm Output Terminal Connection Connection to 24 VAC power supplyConnection to 12 VDC power supply Introduction 9/15 Introduction 10/15 Using PoEAbout the internet connection Introduction 11/15 Introduction 12/15 Press the SET button for 2 seconds or more Adjusting focus Introduction 13/15 Press the NEAR/FAR button to adjust the iris level Introduction 14/15 Introduction 15/15 Quick Operation Guide1/10 Connect the power cable to the power terminals Connect the network LAN socket to your PC using a LAN cableQuick Operation Guide 2/10 Turn on the camera Access the camera from your PCs Web browser Quick Operation Guide 3/10 Quick Operation Guide 4/10 Quick Operation Guide 5/10 Detect Quick Operation Guide 6/10 Quick Operation Guide 7/10 Quick Operation Guide 8/10 Quick Operation Guide 9/10 Optional Configuration Quick Operation Guide 10/10 Before You Begin Network Operation1/13 Access the camera from your Web browser Before You Begin Network Operation 2/13Assign a unique IP address to each camera Monitor live video Before You Begin Network Operation 3/13 Status Before You Begin Network Operation 4/13 Click Auto IP SetupInsert the supplied CD-ROM into the CD-ROM drive of your PC Before You Begin Network Operation 5/13 Select the desired camera and click Manual settingMake changes to the camera data and click Execute Before You Begin Network Operation 6/13 Control Panel, click Network and Internet Connections Before You Begin Network Operation 7/13Click Network Connections Before You Begin Network Operation 8/13 Click Properties Before You Begin Network Operation 9/13 Control Panel, click Network and Sharing Center Before You Begin Network Operation 10/13 Click Manage network connectionsDouble-click Local Area Connection Select the Internet Protocol Version 4 TCP/IPv4 check box Before You Begin Network Operation 11/13 Disabling authentication check at login Before You Begin Network Operation 12/13 Before You Begin Network Operation 13/13 Working with Live Screen1/10 Working with Live Screen 2/10 Type your user name and password and click OKStart Internet Explorer Working with Live Screen 3/10 Working with Live Screen 4/10 Working with Live Screen 5/10 Menu Selection Buttons Working with Live Screen 6/10Other Buttons Working with Live Screen 7/10 Size Working with Live Screen 8/10 Click the Capture button on the tool panel Working with Live Screen 9/10Click Close Starting alarm signal output Stopping alarm signal outputWorking with Live Screen 10/10 Automatic Stop Working with Administrator Configuration Screens1/50 VDC-HD3300/HD300P VDC-HD3100/HD3100P Working with Administrator Configuration Screens 2/50 IP ADDRESS, select Dhcp Working with Administrator Configuration Screens 3/50DDNS, select on Working with Administrator Configuration Screens 4/50 Working with Administrator Configuration Screens 5/50 Http PORT, type your Http port number Working with Administrator Configuration Screens 6/50 TITLE, type the desired camera title and click SET Working with Administrator Configuration Screens 7/50Clock DISPLAY, select the clock display style Working with Administrator Configuration Screens 8/50 Working with Administrator Configuration Screens 9/50 Working with Administrator Configuration Screens 10/50 Working with Administrator Configuration Screens 11/50 Anonymous User LOG IN, select on and click SET Configure the resolution Resolution Working with Administrator Configuration Screens 12/50Configure the image quality Picture Quality Working with Administrator Configuration Screens 13/50 When your selection in Priority is Quality Picture QualityWhen your selection in Priority is Bitrate Bitrate Frame RATE, select the frame rate of the stream Working with Administrator Configuration Screens 14/50 Working with Administrator Configuration Screens 15/50 Configuration Summary for Each Sub Menu Item Working with Administrator Configuration Screens 16/50 Configuring Monitoring ConditionsSwitching between Monitoring Conditions Sense UP, select the electronic sensitivity boosting power Working with Administrator Configuration Screens 17/50 MASKING, select on and click SET Click SET and then Back Working with Administrator Configuration Screens 18/50White BALANCE, select AWC Working with Administrator Configuration Screens 19/50 BLC, select Center and click SET Working with Administrator Configuration Screens 20/50Resize the center metering area Click SET and then Back Working with Administrator Configuration Screens 21/50BLC, select Masking and click SET Working with Administrator Configuration Screens 22/50 Working with Administrator Configuration Screens 23/50 Working with Administrator Configuration Screens 24/50 Manually Configuring Mode-Switching Luminance Level ADJ Working with Administrator Configuration Screens 25/50DAY/NIGHT, select Auto Fixing Camera to Color Video Mode Working with Administrator Configuration Screens 26/50Fixing Camera to Black-and-White Video Mode Vivid Color EFFECT, select on and click SET Working with Administrator Configuration Screens 27/50GAMMA, select the gamma correction level and click SET DNR, select on and click SET Working with Administrator Configuration Screens 28/50Select the Manual check box Working with Administrator Configuration Screens 29/50 MIRROR, select the desired mirror mode and click SETClick ONE Push to focus on the subject Click Privacy Mask in the sub menu Select the Setting Items check box Working with Administrator Configuration Screens 30/50COLOR, select the color of the mask patterns Working with Administrator Configuration Screens 31/50 Working with Administrator Configuration Screens 32/50 Working with Administrator Configuration Screens 33/50 SENSITIVITY, select the detection sensitivity Working with Administrator Configuration Screens 34/50Checking how the motion sensor works Working with Administrator Configuration Screens 35/50 Working with Administrator Configuration Screens 36/50 Working with Administrator Configuration Screens 37/50 Alarm Working with Administrator Configuration Screens 38/50 Alarm OUT1, select Remote Working with Administrator Configuration Screens 39/50 Configure your e-mail server Working with Administrator Configuration Screens 40/50 AUTHENTICATION, select the authentication methodMail ADDRESS, type the recipient e-mail addresses To send a test e-mail, click Test Working with Administrator Configuration Screens 41/50 TRIGGER, select the e-mail transmission conditionsIf you selected Network Failure If you selected Interval SUBJECT, type the subject title of the e-mail Working with Administrator Configuration Screens 42/50TEXT, type the message text and click SET Working with Administrator Configuration Screens 43/50 To use the passive FTP mode, in FTP PASSIVE, select USE Working with Administrator Configuration Screens 44/50 To use a temporary file, set Temporary File to USE Working with Administrator Configuration Screens 45/50 If you selected Alarm IN1/2, MOTION, or Alarm OUT1/2 Working with Administrator Configuration Screens 46/50 Working with Administrator Configuration Screens 47/50 Select the firmware updater file Working with Administrator Configuration Screens 48/50Click SET Working with Administrator Configuration Screens 49/50 Working with Administrator Configuration Screens 50/50 Access LOG A1/10 Cannot access the camera 2/10 3/10 Camera has been suddenly disconnected 4/10 Buttons on the control panel/tool panel do not respond 5/10 Cannot set Shutter to Short or Long 6/10 Cannot display Live video 7/10 Video image is distorted and cannot be displayed correctly 8/10 Live video image is noisy 9/10 E-mail transmission function does not work Upgrade has been terminated 10/10 Copyright Notice/How to Use This Manual1/8 Copyright Notice/How to Use This Manual 2/8 Copyright Notice/How to Use This Manual 3/8 Copyright Notice/How to Use This Manual 4/8 Title window Index windowMain window Previous/Next End 3 ... a B C 123 Copyright Notice/How to Use This Manual 8/8