Introduction 13/15, Adjusting focus | Sanyo VDC-HD3100/HD3100P

3 Adjust the lens orientation. Then adjust angle of view using the zoom ring, and the focus using the buttons.

PEAK HOLD: Shows the value of the maximum focus level.

INDICATOR: Shows the value of the current focus level.

Adjusting focus

1 Use the NEAR/FAR button to roughly focus on the subject.

Adjust by monitoring the video image on the monitor.

2 Press the SET button.

The camera automatically focuses on the subject. Note that the color of the status indicator ( A ) “FOCUSING” turns from black to orange.

If the camera fails to automatically focus on the object, the status indicator ( A ) will indicate “ERROR”. In this case, manually adjust the focus (in Step 3 ).

3 Press the NEAR/FAR button to adjust the focus.

Adjust to set the FA bar ( B ) to the maximum level.

When the subject comes into focus, the color of the status indicator ( A ) “FOCUSING” turns from black to orange.

Pressing the button causes the FB bar ( C ) gauge to move.

The position changes step by step each time the button is pressed and continuously at a high speed when the button is held down.

4 Press the SET button for 2 seconds or more.

The focus adjustment screen will close.

The focus adjustment screen will also close automatically if left idle for 5 minutes or more.

If video is out of focus in either color or black-and-white mode, adjust the focus in respective modes.

Introduction 13/15

Image 13

Sanyo VDC-HD3100/HD3100P, VDC-HD3300/HD300P specifications Introduction 13/15, Adjusting focus

Contents

Introduction1/15 VDC-HD3300/HD300P VDC-HD3100/HD3100P Introduction 2/15 HV/OFF Introduction 3/15 Introduction 4/15 Introduction 5/15 Introduction 6/15 ASSIST/IRIS Settings Introduction 7/15 Introduction 8/15 Alarm Input Terminal Connection Connection to 24 VAC power supply Alarm Output Terminal ConnectionConnection to 12 VDC power supply Introduction 9/15 Introduction 10/15 Using PoEAbout the internet connection Introduction 11/15 Press the SET button for 2 seconds or more Introduction 12/15 Introduction 13/15 Adjusting focus Introduction 14/15 Press the NEAR/FAR button to adjust the iris level Introduction 15/15 Quick Operation Guide1/10 Connect the network LAN socket to your PC using a LAN cable Connect the power cable to the power terminalsQuick Operation Guide 2/10 Turn on the camera Quick Operation Guide 3/10 Access the camera from your PCs Web browser Quick Operation Guide 4/10 Detect Quick Operation Guide 5/10 Quick Operation Guide 6/10 Quick Operation Guide 7/10 Quick Operation Guide 8/10 Quick Operation Guide 9/10 Quick Operation Guide 10/10 Optional Configuration Before You Begin Network Operation1/13 Before You Begin Network Operation 2/13 Access the camera from your Web browserAssign a unique IP address to each camera Monitor live video Status Before You Begin Network Operation 3/13 Before You Begin Network Operation 4/13 Click Auto IP SetupInsert the supplied CD-ROM into the CD-ROM drive of your PC Before You Begin Network Operation 5/13 Select the desired camera and click Manual settingMake changes to the camera data and click Execute Before You Begin Network Operation 6/13 Control Panel, click Network and Internet Connections Before You Begin Network Operation 7/13Click Network Connections Click Properties Before You Begin Network Operation 8/13 Control Panel, click Network and Sharing Center Before You Begin Network Operation 9/13 Click Manage network connections Before You Begin Network Operation 10/13Double-click Local Area Connection Select the Internet Protocol Version 4 TCP/IPv4 check box Before You Begin Network Operation 11/13 Before You Begin Network Operation 12/13 Disabling authentication check at login Before You Begin Network Operation 13/13 Working with Live Screen1/10 Working with Live Screen 2/10 Type your user name and password and click OKStart Internet Explorer Working with Live Screen 3/10 Working with Live Screen 4/10 Working with Live Screen 5/10 Menu Selection Buttons Working with Live Screen 6/10Other Buttons Size Working with Live Screen 7/10 Working with Live Screen 8/10 Click the Capture button on the tool panel Working with Live Screen 9/10Click Close Stopping alarm signal output Starting alarm signal outputWorking with Live Screen 10/10 Automatic Stop VDC-HD3300/HD300P VDC-HD3100/HD3100P Working with Administrator Configuration Screens1/50 Working with Administrator Configuration Screens 2/50 IP ADDRESS, select Dhcp Working with Administrator Configuration Screens 3/50DDNS, select on Working with Administrator Configuration Screens 4/50 Http PORT, type your Http port number Working with Administrator Configuration Screens 5/50 Working with Administrator Configuration Screens 6/50 TITLE, type the desired camera title and click SET Working with Administrator Configuration Screens 7/50Clock DISPLAY, select the clock display style Working with Administrator Configuration Screens 8/50 Working with Administrator Configuration Screens 9/50 Working with Administrator Configuration Screens 10/50 Anonymous User LOG IN, select on and click SET Working with Administrator Configuration Screens 11/50 Configure the resolution Resolution Working with Administrator Configuration Screens 12/50Configure the image quality Picture Quality When your selection in Priority is Quality Picture Quality Working with Administrator Configuration Screens 13/50When your selection in Priority is Bitrate Bitrate Frame RATE, select the frame rate of the stream Working with Administrator Configuration Screens 14/50 Configuration Summary for Each Sub Menu Item Working with Administrator Configuration Screens 15/50 Configuring Monitoring Conditions Working with Administrator Configuration Screens 16/50Switching between Monitoring Conditions Sense UP, select the electronic sensitivity boosting power MASKING, select on and click SET Working with Administrator Configuration Screens 17/50 Click SET and then Back Working with Administrator Configuration Screens 18/50White BALANCE, select AWC Working with Administrator Configuration Screens 19/50 BLC, select Center and click SET Working with Administrator Configuration Screens 20/50Resize the center metering area Click SET and then Back Working with Administrator Configuration Screens 21/50BLC, select Masking and click SET Working with Administrator Configuration Screens 22/50 Working with Administrator Configuration Screens 23/50 Working with Administrator Configuration Screens 24/50 Manually Configuring Mode-Switching Luminance Level ADJ Working with Administrator Configuration Screens 25/50DAY/NIGHT, select Auto Fixing Camera to Color Video Mode Working with Administrator Configuration Screens 26/50Fixing Camera to Black-and-White Video Mode Vivid Color EFFECT, select on and click SET Working with Administrator Configuration Screens 27/50GAMMA, select the gamma correction level and click SET DNR, select on and click SET Working with Administrator Configuration Screens 28/50Select the Manual check box MIRROR, select the desired mirror mode and click SET Working with Administrator Configuration Screens 29/50Click ONE Push to focus on the subject Click Privacy Mask in the sub menu Select the Setting Items check box Working with Administrator Configuration Screens 30/50COLOR, select the color of the mask patterns Working with Administrator Configuration Screens 31/50 Working with Administrator Configuration Screens 32/50 Working with Administrator Configuration Screens 33/50 SENSITIVITY, select the detection sensitivity Working with Administrator Configuration Screens 34/50Checking how the motion sensor works Working with Administrator Configuration Screens 35/50 Working with Administrator Configuration Screens 36/50 Alarm Working with Administrator Configuration Screens 37/50 Alarm OUT1, select Remote Working with Administrator Configuration Screens 38/50 Configure your e-mail server Working with Administrator Configuration Screens 39/50 AUTHENTICATION, select the authentication method Working with Administrator Configuration Screens 40/50Mail ADDRESS, type the recipient e-mail addresses To send a test e-mail, click Test TRIGGER, select the e-mail transmission conditions Working with Administrator Configuration Screens 41/50If you selected Network Failure If you selected Interval SUBJECT, type the subject title of the e-mail Working with Administrator Configuration Screens 42/50TEXT, type the message text and click SET To use the passive FTP mode, in FTP PASSIVE, select USE Working with Administrator Configuration Screens 43/50 To use a temporary file, set Temporary File to USE Working with Administrator Configuration Screens 44/50 If you selected Alarm IN1/2, MOTION, or Alarm OUT1/2 Working with Administrator Configuration Screens 45/50 Working with Administrator Configuration Screens 46/50 Working with Administrator Configuration Screens 47/50 Select the firmware updater file Working with Administrator Configuration Screens 48/50Click SET Working with Administrator Configuration Screens 49/50 Access LOG Working with Administrator Configuration Screens 50/50 A1/10 2/10 Cannot access the camera Camera has been suddenly disconnected 3/10 Buttons on the control panel/tool panel do not respond 4/10 Cannot set Shutter to Short or Long 5/10 Cannot display Live video 6/10 Video image is distorted and cannot be displayed correctly 7/10 Live video image is noisy 8/10 E-mail transmission function does not work 9/10 10/10 Upgrade has been terminated Copyright Notice/How to Use This Manual1/8 Copyright Notice/How to Use This Manual 2/8 Copyright Notice/How to Use This Manual 3/8 Copyright Notice/How to Use This Manual 4/8 Title window Index windowMain window End Previous/Next 123 3 ... a B C Copyright Notice/How to Use This Manual 8/8