Manuals / Sanyo / Photography / Security Camera

Sanyo VDC-HD3300/HD300P specifications Working with Administrator Configuration Screens 36/50

Models: VDC-HD3100/HD3100P VDC-HD3300/HD300P

1 116

Download 116 pages 37.31 Kb

Page 84

5 In [SENSITIVITY], select the detection sensitivity.

You can adjust the detection sensitivity to prevent unwanted detection. The higher the value, the lower the sensitivity.

1 to 9

Checking how the motion sensor works

Click TEST ( 2 ).

If any motion is detected in a grid cell in the detection area, that cell will be shown in red. Correct the detection conditions as required.

While the sensor is working, this button is labeled as END . To finish checking the motion sensor, click the button.

6 Click SET and then BACK .

The settings are saved and you return to the ALARM SETTINGS screen.

Configure the output conditions for each alarm output terminal.

A	Configuring automatic	Configure the terminal so that it outputs an alarm signal automatically when
alarm output:		an alarm condition is detected.
B	Configuring remote alarm	Configure the terminal so that it outputs an alarm signal when the
output:		corresponding Remote Alarm button is clicked.

Before you start the following procedure, connect an external alarm device to one of the alarm output terminals (“ALARM OUT1” in this example).

For details, refer to the “Alarm Input/Output Terminal Connections” section.

Working with Administrator Configuration Screens 36/50

Image 84

Sanyo VDC-HD3300/HD300P, VDC-HD3100/HD3100P specifications Working with Administrator Configuration Screens 36/50

Contents

VDC-HD3300/HD300P VDC-HD3100/HD3100P Introduction1/15Introduction 2/15 Introduction 3/15 HV/OFFIntroduction 4/15 Introduction 5/15 ASSIST/IRIS Settings Introduction 6/15Introduction 7/15 Alarm Input Terminal Connection Introduction 8/15Alarm Output Terminal Connection Connection to 24 VAC power supplyConnection to 12 VDC power supply Introduction 9/15Using PoE Introduction 10/15About the internet connection Introduction 11/15 Introduction 12/15 Press the SET button for 2 seconds or moreAdjusting focus Introduction 13/15Press the NEAR/FAR button to adjust the iris level Introduction 14/15Introduction 15/15 Quick Operation Guide1/10 Connect the power cable to the power terminals Connect the network LAN socket to your PC using a LAN cableQuick Operation Guide 2/10 Turn on the cameraAccess the camera from your PCs Web browser Quick Operation Guide 3/10Quick Operation Guide 4/10 Quick Operation Guide 5/10 DetectQuick Operation Guide 6/10 Quick Operation Guide 7/10 Quick Operation Guide 8/10 Quick Operation Guide 9/10 Optional Configuration Quick Operation Guide 10/10Before You Begin Network Operation1/13 Access the camera from your Web browser Before You Begin Network Operation 2/13Assign a unique IP address to each camera Monitor live videoBefore You Begin Network Operation 3/13 StatusClick Auto IP Setup Before You Begin Network Operation 4/13Insert the supplied CD-ROM into the CD-ROM drive of your PC Select the desired camera and click Manual setting Before You Begin Network Operation 5/13Make changes to the camera data and click Execute Before You Begin Network Operation 6/13 Before You Begin Network Operation 7/13 Control Panel, click Network and Internet ConnectionsClick Network Connections Before You Begin Network Operation 8/13 Click PropertiesBefore You Begin Network Operation 9/13 Control Panel, click Network and Sharing CenterBefore You Begin Network Operation 10/13 Click Manage network connectionsDouble-click Local Area Connection Select the Internet Protocol Version 4 TCP/IPv4 check boxBefore You Begin Network Operation 11/13 Disabling authentication check at login Before You Begin Network Operation 12/13Before You Begin Network Operation 13/13 Working with Live Screen1/10 Type your user name and password and click OK Working with Live Screen 2/10Start Internet Explorer Working with Live Screen 3/10 Working with Live Screen 4/10 Working with Live Screen 5/10 Working with Live Screen 6/10 Menu Selection ButtonsOther Buttons Working with Live Screen 7/10 SizeWorking with Live Screen 8/10 Working with Live Screen 9/10 Click the Capture button on the tool panelClick Close Starting alarm signal output Stopping alarm signal outputWorking with Live Screen 10/10 Automatic StopWorking with Administrator Configuration Screens1/50 VDC-HD3300/HD300P VDC-HD3100/HD3100PWorking with Administrator Configuration Screens 2/50 Working with Administrator Configuration Screens 3/50 IP ADDRESS, select DhcpDDNS, select on Working with Administrator Configuration Screens 4/50 Working with Administrator Configuration Screens 5/50 Http PORT, type your Http port numberWorking with Administrator Configuration Screens 6/50 Working with Administrator Configuration Screens 7/50 TITLE, type the desired camera title and click SETClock DISPLAY, select the clock display style Working with Administrator Configuration Screens 8/50 Working with Administrator Configuration Screens 9/50 Working with Administrator Configuration Screens 10/50 Working with Administrator Configuration Screens 11/50 Anonymous User LOG IN, select on and click SETWorking with Administrator Configuration Screens 12/50 Configure the resolution ResolutionConfigure the image quality Picture Quality Working with Administrator Configuration Screens 13/50 When your selection in Priority is Quality Picture QualityWhen your selection in Priority is Bitrate Bitrate Frame RATE, select the frame rate of the streamWorking with Administrator Configuration Screens 14/50 Working with Administrator Configuration Screens 15/50 Configuration Summary for Each Sub Menu ItemWorking with Administrator Configuration Screens 16/50 Configuring Monitoring ConditionsSwitching between Monitoring Conditions Sense UP, select the electronic sensitivity boosting powerWorking with Administrator Configuration Screens 17/50 MASKING, select on and click SETWorking with Administrator Configuration Screens 18/50 Click SET and then BackWhite BALANCE, select AWC Working with Administrator Configuration Screens 19/50 Working with Administrator Configuration Screens 20/50 BLC, select Center and click SETResize the center metering area Working with Administrator Configuration Screens 21/50 Click SET and then BackBLC, select Masking and click SET Working with Administrator Configuration Screens 22/50 Working with Administrator Configuration Screens 23/50 Working with Administrator Configuration Screens 24/50 Working with Administrator Configuration Screens 25/50 Manually Configuring Mode-Switching Luminance Level ADJDAY/NIGHT, select Auto Working with Administrator Configuration Screens 26/50 Fixing Camera to Color Video ModeFixing Camera to Black-and-White Video Mode Working with Administrator Configuration Screens 27/50 Vivid Color EFFECT, select on and click SETGAMMA, select the gamma correction level and click SET Working with Administrator Configuration Screens 28/50 DNR, select on and click SETSelect the Manual check box Working with Administrator Configuration Screens 29/50 MIRROR, select the desired mirror mode and click SETClick ONE Push to focus on the subject Click Privacy Mask in the sub menuWorking with Administrator Configuration Screens 30/50 Select the Setting Items check boxCOLOR, select the color of the mask patterns Working with Administrator Configuration Screens 31/50 Working with Administrator Configuration Screens 32/50 Working with Administrator Configuration Screens 33/50 Working with Administrator Configuration Screens 34/50 SENSITIVITY, select the detection sensitivityChecking how the motion sensor works Working with Administrator Configuration Screens 35/50 Working with Administrator Configuration Screens 36/50 Working with Administrator Configuration Screens 37/50 AlarmWorking with Administrator Configuration Screens 38/50 Alarm OUT1, select RemoteWorking with Administrator Configuration Screens 39/50 Configure your e-mail serverWorking with Administrator Configuration Screens 40/50 AUTHENTICATION, select the authentication methodMail ADDRESS, type the recipient e-mail addresses To send a test e-mail, click TestWorking with Administrator Configuration Screens 41/50 TRIGGER, select the e-mail transmission conditionsIf you selected Network Failure If you selected IntervalWorking with Administrator Configuration Screens 42/50 SUBJECT, type the subject title of the e-mailTEXT, type the message text and click SET Working with Administrator Configuration Screens 43/50 To use the passive FTP mode, in FTP PASSIVE, select USEWorking with Administrator Configuration Screens 44/50 To use a temporary file, set Temporary File to USEWorking with Administrator Configuration Screens 45/50 If you selected Alarm IN1/2, MOTION, or Alarm OUT1/2Working with Administrator Configuration Screens 46/50 Working with Administrator Configuration Screens 47/50 Working with Administrator Configuration Screens 48/50 Select the firmware updater fileClick SET Working with Administrator Configuration Screens 49/50 Working with Administrator Configuration Screens 50/50 Access LOGA1/10 Cannot access the camera 2/103/10 Camera has been suddenly disconnected4/10 Buttons on the control panel/tool panel do not respond5/10 Cannot set Shutter to Short or Long6/10 Cannot display Live video7/10 Video image is distorted and cannot be displayed correctly8/10 Live video image is noisy9/10 E-mail transmission function does not workUpgrade has been terminated 10/10Copyright Notice/How to Use This Manual1/8 Copyright Notice/How to Use This Manual 2/8 Copyright Notice/How to Use This Manual 3/8 Copyright Notice/How to Use This Manual 4/8 Index window Title windowMain window Previous/Next End3 ... a B C 123Copyright Notice/How to Use This Manual 8/8