Loading Paper, Push the paper tray in, until it stops | Savin 4018d

KirC2_ENcopyF_FM.book Page 43 Monday, September 22, 2003 11:36 AM

B Loading Paper

Reference

For paper types and sizes, see Gen- eral Settings Guide.

Loading Paper

Note

❒You can change the paper size, see General Settings Guide.

❒This illustration shows the paper trays (1 or 2).

A Pull the paper tray out slowly un- til it stops.

B Square the paper and load it in the tray.

AAI022S

Important

❒Check the top of the stack is not higher than the limit mark in- side the tray.

Note

❒Fan the paper before loading.

❒Straighten curled or warped pa- per before loading.

❒When using paper tray 1 or 2, before loading paper, push down the metal plate.

C Push the paper tray in, until it stops.

B Loading Paper

3

43

Image 51

Savin 4018d, 4015 manual Loading Paper, Push the paper tray in, until it stops

Contents

Copy Reference Introduction Manuals for This Machine Manuals for DeskTopBinder V2 Lite Manuals for ScanRouter V2 LiteOther manuals Table of Contents If Your Machine Does Not Operate As You Want Accessing User Tools Copier FeaturesSettings You Can Change with User Tools Dos and Donts Where to Put Your Machine Combination Chart Supplementary Information SpecificationsPage Page Remarque concernant les utilisateurs au Canada Avertissement How to Read This Manual SymbolsNames of Major Options Safety During Operation Safety InformationPage AAI029S Machine Types Options fully installed Control PanelCopier only Lighter and Darker Cancel keyCombine/Series key Sort key Reading the Display and Using Keys DisplayInitial copy display Scroll keys Operation switch right side of the control panel Turning On the PowerTurning On the Main Power Turning On the Power Turning Off the Main Power Turning Off the Power Saving Energy Auto Off/ Low Power Inch version Sizes and Weights of Recommended OriginalsOriginals Metric version Sizes Detectable with Auto Paper Select Sizes difficult to detect Missing Image AreaExposure glass ADF or Ardf Placing Originals Original OrientationPlacing Originals on the Exposure Glass Limit mark Document guide Ardf Placing custom size originals To clear an entered value Basic ProcedureTo switch between pages or select functions To stop the machine during a multi- copy run Paper guide release lever Copying from the Bypass TrayOpen the bypass tray Push up the paper guide release lever Pull down the paper guide release the lever step B Select Paper Size using U or T, and then press the OK keySelect Regular Size using U or T, and then press the OK key Horizontal size Vertical size Extender Paper guides Then press the OK Select Paper Size using U orSelect Custom Size using U or T, and then press the OK key Feeds Select Thick Paper using U or T, and then press the OK key Selecting Copy Paper Adjusting Image DensitySelecting Original Type Setting Copier Functions Preset Reduce/Enlarge Select the paper tray or bypass tray using U or TMake sure Auto Paper Select is se- lected Zoom Base PointPress Reduce or Enlarge Press the OK key Adjust the ratio using U or TAuto Reduce/Enlarge Enter the ratio Sort Rotate SortSort Select Sort or Rotate Sort, and then press the OK key Duplex Type 3 onlySided → 2 Sided Sided → 2 Sided Optional Ardf is required Press the Duplex key Original orientation and completed copies Sided 1 Page → Combine 1 Side Optional Ardf is required One-Sided CombineSided 2 Pages → Combine 1 Side Sided 4 Pages → Combine 1 Side Orientation of the original and image Optional Ardf is requiredPosition of combine Sided 2 Pages → Combine 1 Side Sided 4 Pages → Combine 2 Side Two-Sided Combine Type 3 onlySided 8 Pages → Combine 2 Side Sided 4 Pages → Combine 2 Side Optional Ardf is required Then press the OK key Top or Top to Bottom using U or Press the Combine/Series key Series CopiesSided→1 Sided Optional Ardf is required Book→1 Sided Place your original, and then press the Start key Select the paper tray using U or T If Your Machine Does Not Operate As You Want When a Message Is Displayed If You Cannot Make Clear Copies Problem Causes Solutions Combine If You Cannot Make Copies As You WantBasic Edit Duplex Type 3 only When Memory Is Full Loading Paper Loading PaperPush the paper tray in, until it stops Original Orientation Orientation-Fixed Paper or Two-Sided Paper Loaded paper orientation For MFP Used Toner Adding TonerHandling Toner Toner Storage Removing Toner Inserting Toner Troubleshooting Accessing User Tools Copier Features Changing Default SettingsPress the User Tools/Counter key Change is made, and the ma- chine is ready to copy Quitting User Tools APS/ Auto R/E Priority Settings You Can Change with User ToolsAuto Tray Switching Original Type Setting Original Count Display Duplex Mode PriorityOrientation Max. Number of Sets Rotate Sort Preset R/E PriorityLetterhead Setting Duplex Margin User Tools Copier Features Dos and Donts Remarks Environments to avoid Where to Put Your MachineMachine Environment Optimum environmental conditions Moving Power Connection Access to the Machine Cleaning the machine Cleaning the Exposure GlassCleaning the Exposure Glass Cover Cleaning the ADF or Ardf Remarks Combination Chart Specifications Preset Enlarge/Reduce Supplementary InformationBypass Tray Copy Sort, Rotate Sort Zoom Duplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607