Inserting Toner | Savin 4018d, 4015 specification

KirC2_ENcopyF_FM.book Page 49 Monday, September 22, 2003 11:36 AM

Inserting Toner

Inserting Toner

•1: Hold the new bottle horizontally and

shake it from side to side five or six times. 2: Remove the black cap.

Note

❒ Do not remove the black cap before shaking.

❒ Do not remove the inner cap.

3

• 3: Put the toner bottle on the holder, and then pull its top forward.

•4: Push in the green lever until it clicks.

• 5: Press down the green lever.

• 6: Close the machine's front cover.

49

Image 57

Savin 4018d, 4015 manual Inserting Toner

Contents

Copy Reference Introduction Manuals for This Machine Manuals for DeskTopBinder V2 Lite Manuals for ScanRouter V2 LiteOther manuals Table of Contents Settings You Can Change with User Tools Accessing User Tools Copier FeaturesDos and Donts Where to Put Your Machine If Your Machine Does Not Operate As You Want Combination Chart Supplementary Information SpecificationsPage Page Remarque concernant les utilisateurs au Canada Avertissement How to Read This Manual SymbolsNames of Major Options Safety During Operation Safety InformationPage AAI029S Machine Types Options fully installed Control PanelCopier only Combine/Series key Cancel keySort key Lighter and Darker Reading the Display and Using Keys DisplayInitial copy display Scroll keys Turning On the Main Power Turning On the PowerTurning On the Power Operation switch right side of the control panel Turning Off the Main Power Turning Off the Power Saving Energy Auto Off/ Low Power Originals Sizes and Weights of Recommended OriginalsMetric version Inch version Sizes Detectable with Auto Paper Select Exposure glass Missing Image AreaADF or Ardf Sizes difficult to detect Placing Originals Original OrientationPlacing Originals on the Exposure Glass Limit mark Document guide Ardf Placing custom size originals To switch between pages or select functions Basic ProcedureTo stop the machine during a multi- copy run To clear an entered value Open the bypass tray Copying from the Bypass TrayPush up the paper guide release lever Paper guide release lever Select Regular Size using U or T, and then press the OK key Select Paper Size using U or T, and then press the OK keyHorizontal size Vertical size Extender Paper guides Pull down the paper guide release the lever step B Select Custom Size using U or T, and then press the OK key Select Paper Size using U orFeeds Then press the OK Select Thick Paper using U or T, and then press the OK key Selecting Original Type Setting Adjusting Image DensityCopier Functions Selecting Copy Paper Preset Reduce/Enlarge Select the paper tray or bypass tray using U or TMake sure Auto Paper Select is se- lected Zoom Base PointPress Reduce or Enlarge Auto Reduce/Enlarge Adjust the ratio using U or TEnter the ratio Press the OK key Sort Rotate SortSort Sided → 2 Sided Duplex Type 3 onlySided → 2 Sided Optional Ardf is required Select Sort or Rotate Sort, and then press the OK key Press the Duplex key Original orientation and completed copies Sided 2 Pages → Combine 1 Side One-Sided CombineSided 4 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is required Position of combine Optional Ardf is requiredSided 2 Pages → Combine 1 Side Orientation of the original and image Sided 8 Pages → Combine 2 Side Two-Sided Combine Type 3 onlySided 4 Pages → Combine 2 Side Optional Ardf is required Sided 4 Pages → Combine 2 Side Then press the OK key Top or Top to Bottom using U or Sided→1 Sided Optional Ardf is required Series CopiesBook→1 Sided Press the Combine/Series key Place your original, and then press the Start key Select the paper tray using U or T If Your Machine Does Not Operate As You Want When a Message Is Displayed If You Cannot Make Clear Copies Problem Causes Solutions Basic If You Cannot Make Copies As You WantEdit Combine Duplex Type 3 only When Memory Is Full Loading Paper Loading PaperPush the paper tray in, until it stops Original Orientation Orientation-Fixed Paper or Two-Sided Paper Loaded paper orientation For MFP Handling Toner Adding TonerToner Storage Used Toner Removing Toner Inserting Toner Troubleshooting Accessing User Tools Copier Features Changing Default SettingsPress the User Tools/Counter key Change is made, and the ma- chine is ready to copy Quitting User Tools Auto Tray Switching Settings You Can Change with User ToolsOriginal Type Setting APS/ Auto R/E Priority Orientation Duplex Mode PriorityMax. Number of Sets Original Count Display Letterhead Setting Preset R/E PriorityDuplex Margin Rotate Sort User Tools Copier Features Dos and Donts Remarks Machine Environment Where to Put Your MachineOptimum environmental conditions Environments to avoid Moving Power Connection Access to the Machine Cleaning the Exposure Glass Cover Cleaning the Exposure GlassCleaning the ADF or Ardf Cleaning the machine Remarks Combination Chart Specifications Preset Enlarge/Reduce Supplementary InformationBypass Tray Copy Sort, Rotate Sort Zoom Duplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607