Access to the Machine | Savin 4018d, 4015 specs

KirC2_ENcopyF_FM.book Page 60 Monday, September 22, 2003 11:36 AM

Remarks

5

60

Access to the Machine

Place the machine near the power source, providing the clearance areas shown.

1.Rear: 5 cm (2") or more

2.Right: 25 cm (10") or more

3.Front: 75 cm (29.6") or more

4.Left: 15 cm (6") or more

Note

❒For the required space when op- tions are installed, contact your service representative.

Image 68

Savin 4018d, 4015 manual Access to the Machine

Contents

Copy Reference Introduction Manuals for This Machine Other manuals Manuals for DeskTopBinder V2 LiteManuals for ScanRouter V2 Lite Table of Contents Accessing User Tools Copier Features Settings You Can Change with User ToolsDos and Donts Where to Put Your Machine If Your Machine Does Not Operate As You Want Specifications Combination Chart Supplementary InformationPage Page Remarque concernant les utilisateurs au Canada Avertissement Names of Major Options How to Read This ManualSymbols Safety Information Safety During OperationPage AAI029S Machine Types Copier only Options fully installedControl Panel Cancel key Combine/Series keySort key Lighter and Darker Initial copy display Reading the Display and Using KeysDisplay Scroll keys Turning On the Power Turning On the Main PowerTurning On the Power Operation switch right side of the control panel Turning Off the Power Turning Off the Main Power Auto Off/ Low Power Saving Energy Sizes and Weights of Recommended Originals OriginalsMetric version Inch version Sizes Detectable with Auto Paper Select Missing Image Area Exposure glassADF or Ardf Sizes difficult to detect Placing Originals on the Exposure Glass Placing OriginalsOriginal Orientation Ardf Limit mark Document guide Placing custom size originals Basic Procedure To switch between pages or select functionsTo stop the machine during a multi- copy run To clear an entered value Copying from the Bypass Tray Open the bypass trayPush up the paper guide release lever Paper guide release lever Select Paper Size using U or T, and then press the OK key Select Regular Size using U or T, and then press the OK keyHorizontal size Vertical size Extender Paper guides Pull down the paper guide release the lever step B Select Paper Size using U or Select Custom Size using U or T, and then press the OK keyFeeds Then press the OK Select Thick Paper using U or T, and then press the OK key Adjusting Image Density Selecting Original Type SettingCopier Functions Selecting Copy Paper Make sure Auto Paper Select is se- lected Preset Reduce/EnlargeSelect the paper tray or bypass tray using U or T Press Reduce or Enlarge ZoomBase Point Adjust the ratio using U or T Auto Reduce/EnlargeEnter the ratio Press the OK key Sort SortRotate Sort Duplex Type 3 only Sided → 2 SidedSided → 2 Sided Optional Ardf is required Select Sort or Rotate Sort, and then press the OK key Original orientation and completed copies Press the Duplex key One-Sided Combine Sided 2 Pages → Combine 1 SideSided 4 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is required Optional Ardf is required Position of combineSided 2 Pages → Combine 1 Side Orientation of the original and image Two-Sided Combine Type 3 only Sided 8 Pages → Combine 2 SideSided 4 Pages → Combine 2 Side Optional Ardf is required Sided 4 Pages → Combine 2 Side Top or Top to Bottom using U or Then press the OK key Series Copies Sided→1 Sided Optional Ardf is requiredBook→1 Sided Press the Combine/Series key Select the paper tray using U or T Place your original, and then press the Start key When a Message Is Displayed If Your Machine Does Not Operate As You Want Problem Causes Solutions If You Cannot Make Clear Copies If You Cannot Make Copies As You Want BasicEdit Combine When Memory Is Full Duplex Type 3 only Push the paper tray in, until it stops Loading PaperLoading Paper Orientation-Fixed Paper or Two-Sided Paper Original Orientation Loaded paper orientation For MFP Adding Toner Handling TonerToner Storage Used Toner Removing Toner Inserting Toner Troubleshooting Press the User Tools/Counter key Accessing User Tools Copier FeaturesChanging Default Settings Quitting User Tools Change is made, and the ma- chine is ready to copy Settings You Can Change with User Tools Auto Tray SwitchingOriginal Type Setting APS/ Auto R/E Priority Duplex Mode Priority OrientationMax. Number of Sets Original Count Display Preset R/E Priority Letterhead SettingDuplex Margin Rotate Sort User Tools Copier Features Remarks Dos and Donts Where to Put Your Machine Machine EnvironmentOptimum environmental conditions Environments to avoid Power Connection Moving Access to the Machine Cleaning the Exposure Glass Cleaning the Exposure Glass CoverCleaning the ADF or Ardf Cleaning the machine Remarks Specifications Combination Chart Bypass Tray Copy Preset Enlarge/ReduceSupplementary Information Zoom Sort, Rotate Sort Duplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607