Active LED, Ready LED | Schneider Optics Modicon Quantum Ethernet

Maintenance

The Run indicator will flash. The Coll LED also may flash, indicating that collisions are occurring on the Ethernet network. Such collisions are normal.

If a fault has occurred, the normal LEDs may be extinguished or other indicators may light. This section will discuss errors reported by the Active, Ready, Coll, Link, Kernel, Appl and Fault indicators.

For each type of error, try the suggested remedies in the order given. If no remedy suggested here overcomes the error, consult your Schneider Automation customer representative.

Certain error codes are recorded in the MSTR block. For instructions on how to read and interpret those codes through Modsoft, please refer to MSTR Function Error Codes on page 28.

6.1.2Active LED

If the Active LED fails to light, the module is not communicating with the backplane.

Troubleshooting 1. Make sure the Ethernet web embedded server module and the controller are installed properly. Verify that the controller is functioning.

If the controller is not functioning, replace it. If neither the new controller nor the Ethernet module will function, replace the backplane.

2.Make sure that no more than two network option modules -- including NOE, NOM, NOP and CRP 811 modules -- have been installed in the backplane with a 140 CPU 113 or 213; no more than six network option modules with a 140 CPU 424, 434 or 534.

3.Check the version of the controller executive. You must have version 1.1 or greater to support the Ethernet web embedded server module. Earlier versions do not recognize the module.

4.Replace and return the faulty Ethernet web embedded server module.

6.1.3Ready LED

If the Ready LED fails to light, the module has failed internal diagnostic tests.

Troubleshooting 1. Make sure that power has been applied to the backplane.

2.Replace and return the faulty Ethernet web embedded server module.

54	840 USE 115 00 Version 1.0

Image 64

Schneider Optics Modicon Quantum Ethernet manual Active LED, Ready LED

Contents

Modicon Quantum Ethernet USE 115 00 Version Training USE 115 00 Vesion Modicon Quantum EthernetOctober Document Set Preface USE 115 00 Version Contents Using the Network Options Ethernet Tester Chapter MaintenanceMstr Instruction Retrieving Data via the World Wide Web Appendix a Specifications Appendix D Suppliers Glossary Index Contents Viii About This Book Document Scope Validity Note Related Documentation Introduction Ethernet Web Embedded Server Modules Benefits of Quantum Design Models for Fiber Optic and Twisted Pair Cable Systems Type of Cable Network Part Number Front Panel Components Removable Door 140 NOE 251 Color Indication When On LED Display Address Labels EthernetAddress Label Internet Protocol IP Network Address Label Example Calculating the Derived IP Network Address Locate the global address label onFront panel of the module 0 B 7 2 a Fiber Optic Connectors Twisted Pair ConnectorTransmit Data Network Options Ethernet Tester Utility DisketteErrlog Ethernet and Your Application Meeting the Demands of Your Application Compatibility Guidelines for Designing Your Network Delays Using SwitchesSegregating Traffic Installing and Configuring Module Before You Begin Verifying the Default Configuration Verifying that the Network Has Been Constructed Properly Improper Network Topologies Are You Really Ready to Install? Check Installing the ModuleMounting the Module on the Backplane Connecting the Cable With connectors 990 XCA 656Twisted Pair Snap into place Attaching the Cable Changing the Default Configuration Configuring the Module with Modsoft Selecting the Ethernet Framing Type Assigning a Slot Number Resetting the Module Assigning the Default Gateway Address and Subnet MaskAssigning the IP Network Address Configuring More Than One Ethernet Module Configuring the Module with Concept Parameter Dialog for an Ethernet Web Embedded Server Module Mstr Description Mstr Instruction IntroductionMstr Operation Code TCP/IP Ethernet Support Characteristics SizeCompatibility Opcode BF hex Content RepresentationInputs Outputs Mstr Function Error Codes Error CodesMiddle Node Bottom Node Hex Error Code Meaning Ss Hex value Meaning Hex Error Code Meaning 5016 An argument is valid Read and Write Mstr Operations Control BlockUtilization Information as described in the following table Get Local Statistics Mstr Operation Statistics information as described in the following table Clear Local Statistics Mstr Operation Get Remote Statistics Mstr Operation Clear Remote Statistics Mstr Operation Peer Cop Health Mstr Operation Peer CopCommunications Health Status Type Word Status Index Read CTE Config Extension Table Mstr Operation Reset Option Module Mstr OperationModule information as described in the following table Parameter Register Content CTE DisplayImplementation Registers. The registers display the following CTE data Write CTE Config Extension Table Mstr Operation 13 TCP/IP Ethernet Statistics Word Meaning Retrieving Data via the World Wide Web Introduction Accessing the Web Utility Home Web Utility Home Web Utility for Quantum Quantum Web Utility Retrieving Data via the World Wide Web Using the Network Options Ethernet Tester Introduction Installing the Network Options Ethernet Tester Establishing a Connection with an Ethernet Module Main Menu Getting and Clearing Statistics Get Statistics Box MAC Address Sample Statistics Using the Network Options Ethernet Tester Reading and Writing Registers Read Register Box Write Register Box Maintenance Responding to Errors Detecting Errors Active LED Ready LED Link LED Fault LEDKernel LED Collision LED LED Display for Improperly Connected Twisted Pair Cable Reading and Clearing the Error Log Application LED Default is Example Errlog 49 EBX, EBP, ESI, EDI, ESP, EFLAGS, EIP Example Sample Error Log To restart the controller, type Y Hot Swapping An Ethernet Module Downloading a New Software Image From the Device to Download menu, select Local Head USE 115 00 Version Specifications Power Dissipation Bus Current Required Operating ConditionsCommunication Ports Storage Conditions Specifications Ethernet Developers Guide Introduction References Overview Development Environment Class Descriptions CSampledoc Class CSampleView Class Accessing TCP/IPEvent Description Application Message Format Network Event Member Function Timers Transaction Processing Transmit State Machine Exists the loop Receive State Machine Ethernet Developers Guide Displaying on the Screen Quantum Ethernet TCP/IP Modbus Application Protocol Modbus Application Protocol PDU Includes the dstid and data fieldsIs defined below Counts and data offsets Modbus Application Protocol Service Classes Modbus Application Protocol PDU Analysis Quantum Ethernet TCP/IP Modbus Application Protocol Broadcast/Multicast TCP/IP Specific IssuesTCP Port Number Reference Documents Quantum Ethernet TCP/IP Modbus Application Protocol Suppliers Suppliers Glossary AddressBps Bridge Default gateway FieldFrame Framing types Hub InternetIP Address IO Map OSI model PacketPort Protocol Switch SocketStack Subnet Glossary Index Index Mstr Network Options Ethernet Tester World Wide Web server